هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
The Tube-in-the-Back Fountain Brush: Turn the Tube and the Jets Become a Soak
YourGrandma

ایجاد شده توسط

YourGrandma

6. اکتبر 2026IS
۱۷
۰
۰
۰
۰

The Tube-in-the-Back Fountain Brush: Turn the Tube and the Jets Become a Soak

A scrubbing brush dipped in a bucket runs dry in seconds, and a hose beside it floods the floor. Annie B. Landreth of Bristol, Pennsylvania, received US 757,628, dated 19 April 1904, for a fountain brush "of great simplicity of construction": a recess bored lengthwise into an ordinary brush's back with openings to its face, and a perforated tube on a cock that slides in; a square plate on the tube sits in a square depression, so the holes can face the openings or be turned a quarter turn against the recess walls. This rung compares the jet with the turned-away flow, then bores a scrub brush, fits a tube and tap, and measures both settings.
متوسط
About 3 hours

دستورالعمل‌ها

1

Jet against soak

در حال بارگذاری دفترچهٔ Jupyter…
2

A scrubbing brush improved before it

The embedded blueprint holds two brush heads on a sprung holder. Landreth leaves the brush ordinary and feeds water through a bore in its back.
3

Read US 757,628

"Thus the perforations may register with the openings a² a², as indicated in Fig. 5, or the fountain-tube may be turned to an angle of ninety degrees, so that the perforations C' face the lateral sides of the recess A', as indicated in Fig. 6, and in this way the force due to the pressure of the water-supply is broken and the water will pass out of the openings without force."
4

Bore the back

Clamp a scrub brush with a back at least 22 mm thick, bristles down. Drill a 12 mm hole 160 mm deep along the back's centre from one end, keeping the bit level.

مواد مورد نیاز این مرحله:

برس سایشبرس سایش1 قطعه

ابزارهای مورد نیاز:

گیرهٔ رومیزیگیرهٔ رومیزی
دریل شارژیدریل شارژی
مجموعهٔ متهٔ نوک‌مرکزیمجموعهٔ متهٔ نوک‌مرکزی
خط‌کشخط‌کش
عینک ایمنی شفافعینک ایمنی شفاف
5

Drill the openings

From the bristle face, between rows, drill seven 3 mm holes into the bore, 20 mm apart.

ابزارهای مورد نیاز:

دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
ماژیک ثابتماژیک ثابت
6

Cut the square depression

Round the bore's mouth, chisel a 30 mm square 2 mm deep.

ابزارهای مورد نیاز:

مجموعه اسکنهٔ چوبمجموعه اسکنهٔ چوب
چکشچکش
خط‌کشخط‌کش
7

Make the tube

Cut 160 mm of 10 mm copper tube. Squeeze one end shut in the vice and solder it. Drill seven 1.8 mm holes in a line to match the openings.

مواد مورد نیاز این مرحله:

لولهٔ مسی ۱۰ میلی‌متریلولهٔ مسی ۱۰ میلی‌متری1 قطعه
سیم لحیم لوله‌کشی بی‌سربسیم لحیم لوله‌کشی بی‌سرب1 قطعه
روان‌ساز لوله‌کشیروان‌ساز لوله‌کشی1 قطعه

ابزارهای مورد نیاز:

لوله‌برلوله‌بر
گیرهٔ رومیزیگیرهٔ رومیزی
مشعل پروپانمشعل پروپان
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
دستکش گرمااستواردستکش گرمااستوار
8

Solder on the square plate

Cut a 28 mm square of brass sheet, drill it 10 mm in the centre, slide it on 160 mm from the closed end with one edge square to the holes, and solder it.

مواد مورد نیاز این مرحله:

ورق برنجورق برنج1 قطعه
سیم لحیم لوله‌کشی بی‌سربسیم لحیم لوله‌کشی بی‌سرب1 قطعه
روان‌ساز لوله‌کشیروان‌ساز لوله‌کشی1 قطعه

ابزارهای مورد نیاز:

قیچی ورق‌بریقیچی ورق‌بری
دریل شارژیدریل شارژی
مجموعه متهمجموعه مته
مشعل پروپانمشعل پروپان
دستکش گرمااستواردستکش گرمااستوار
9

Fit the tap and button

Fit the ball valve and a hose connector to the open end with brass fittings and PTFE tape. Screw a 10 × 40 mm brass strip beside the depression as a turn-button.

مواد مورد نیاز این مرحله:

شیر توپیشیر توپی1 قطعه
اتصالات برنجیاتصالات برنجی1 قطعه
نوار آب‌بندی رزوه از PTFEنوار آب‌بندی رزوه از PTFE1 قطعه
ورق برنجورق برنج1 قطعه
پیچ چوب #8 در ۱ اینچپیچ چوب #8 در ۱ اینچ1 قطعه

ابزارهای مورد نیاز:

آچار فرانسهآچار فرانسه
مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
10

The build in 3D

FreeCAD model of this build, not of the patent: a 200 × 60 × 26 mm back with a 12 mm bore 160 mm deep, seven 3 mm openings, a 30 mm square depression, the perforated tube with its square plate, valve and turn-button.
فایل طراحیBLENDCC0 - Free
11

Compare the two settings

Connect the garden hose. With the holes facing the openings, hold the brush face-up and measure how high the jets rise; time a litre into the jug. Turn the tube 90°, lock it, and repeat.
مرحله 11 - Image 1

مواد مورد نیاز این مرحله:

شلنگ باغبانیشلنگ باغبانی1 قطعه
آبآب1 قطعه

ابزارهای مورد نیاز:

خط‌کشخط‌کش
پارچ اندازه‌گیریپارچ اندازه‌گیری
کرونومترکرونومتر
12

A brush that sprays, leaks or will not lock

Tube-in-the-back fountain brush troubleshooting.

Flow

Loading...
13

History and honest limits

**Annie B. Landreth** of Bristol, Pennsylvania, filed US 757,628 on 1 April 1902; it is dated 19 April 1904. The nozzle carries a cock and the usual hose coupling; the square plate and depression may be any shape that holds the tube at the chosen angle, and a turn-button holds it in use. The attachment can be inserted and withdrawn instantly, leaving the sides and back free to hold the brush in the ordinary way. **Honest limits.** She gives no sizes; ours are examples. The notebook ignores the loss in the bore. Your jet heights and times are the result.

مواد

11

ابزارهای لازم

17

فایل‌های طراحی

1

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...