همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Vacuum Gauge: Flattened Curved Tube Driving an Index (Bourdon, US 9,163)
Emma

ایجاد شده توسط

Emma

9. نوامبر 2026SE
۶
۰
۰
۰
۰

Vacuum Gauge: Flattened Curved Tube Driving an Index (Bourdon, US 9,163)

A vacuum gauge shows how far a line or vessel has been pumped below atmospheric pressure. Eugène Bourdon (US 9,163, 1852) found that a thin metal tube, flattened and bent into a curve, straightens a little under internal pressure and curls up more when the air is drawn out of it. One end is open to the line through a cock; the closed end drives a lever on a spindle that carries the index. With the air withdrawn the index moves the opposite way to a pressure gauge, "and the instrument is then a vacuum gage." Source: E. Bourdon, "Pressure-Gage", US Patent 9,163 (1852). Picture: its Figs. 1-6.
پیشرفته
Unknown

دستورالعمل‌ها

1

Read Bourdon

"If the air be withdrawn from the interior of the tube A by means of an air pump or otherwise the curvature of the tube is increased and the index moves in the opposite direction and the instrument is then a vacuum gage."
2

Make the tube

Flatten a thin metal tube so its section is no longer round (Bourdon draws oval, flat, cross and Y sections) and bend it into a near circle. Close one end (how is not given) and leave the other open. Bourdon: the wall depends on the size, motion, pressure and metal; his only figure is brass about 1/100 in. thick for a barometer about 4 in. across. The metal, wall and size for the vacuum gauge are not given.

مواد مورد نیاز این مرحله:

فلز نامعلومفلز نامعلوم1 tube

ابزارهای مورد نیاز:

روش شکل‌دهی ناشناختهروش شکل‌دهی ناشناخته
ابعاد نامعلومابعاد نامعلوم
3

Fit the movement

Fix the open end of the tube in the case, connected through a cock to a pipe to the line or vessel. Join the closed end by a link to a short lever on a small spindle that carries the index (or drive the spindle by a toothed sector and pinion, or by a silk thread wound round it and kept tight by a spring). The lever multiplies the tube's movement at the index.

مواد مورد نیاز این مرحله:

شیر ناشناختهشیر ناشناخته1 cock
فلز نامعلومفلز نامعلوم1 link, lever, spindle and index
فلز نامعلومفلز نامعلوم1 case

ابزارهای مورد نیاز:

دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
سوهان (سوهان دستی)سوهان (سوهان دستی)
4

Graduate the dial

Fit a dial behind the index. Bourdon graduates the arc by submitting the instrument to known pressures alongside an ordinary mercury gauge and marking each on the dial; equal steps of pressure give nearly equal degrees. Connect the gauge to a pump drawing the air out: the tube curls more and the index moves the opposite way to a pressure gauge. The reference used to mark a vacuum scale is not given.

مواد مورد نیاز این مرحله:

ماده ناشناختهماده ناشناخته1 dial

ابزارهای مورد نیاز:

پمپ خلأپمپ خلأ

مواد

3

ابزارهای لازم

6

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...