همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Laminated Rubber Mallet: A Rubber-and-Canvas Head Locked on a Flared Handle by an Internal Rib (Whisler, 1924)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۱۱
۰
۰
۰
۰

Laminated Rubber Mallet: A Rubber-and-Canvas Head Locked on a Flared Handle by an Internal Rib (Whisler, 1924)

Chauncy P. Whisler of Kenmore, Ohio, received US 1,501,827, dated 15 July 1924, for The Miller Rubber Company of Akron. It solves how to fix a handle in a head that is itself elastic. The rubber-and-fabric head has an eye that flares outwards, with a narrow rib at the handle side. The handle has a matching flared end, a groove for the rib and a shoulder. It is pushed right through the warm head from the outer face until the rib snaps into the groove. The flare stops the head flying off and the rib stops it sliding up the handle. We build the head from rubber sheet and canvas, ply by ply, as his "stepped conical eye". The sizes are ours.
مبتدی
About 2 days

دستورالعمل‌ها

1

The stepped eye and the stretch at the rib

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 1,501,827

"When in position, the flared end 1a of the handle absolutely precludes the head from flying off when delivering blows and the rib and groove engagement prevents any inward displacement of the head."
3

Print the ply template

Full-size A4 template: the 110 x 60 mm ply and the hole circle for each of the 17 plies, largest at the outer face. Print at 100 %; its 50 mm bar must measure 50 mm.
فایل طراحیPDFCC0 - Free
4

Cut the plies

Cut 17 plies of 3 mm natural rubber sheet 110 x 60 mm and 14 of cotton canvas the same size. Glue each paper circle from the template in the middle of its ply, numbered 1 to 17, and cut the hole round it with a sharp craft knife, holding the blade upright. Cut the same hole in a canvas ply for each of plies 1 to 14.

مواد مورد نیاز این مرحله:

ورق لاستیک طبیعیورق لاستیک طبیعی2 قطعه
کرباس پنبه‌ایکرباس پنبه‌ای1 قطعه

ابزارهای مورد نیاز:

چاپگر جوهرافشانچاپگر جوهرافشان
چسبچسب
چاقوی کاردستیچاقوی کاردستی
گونیای ترکیبیگونیای ترکیبی
5

Laminate the head

Brush contact cement on both faces to be joined, let it go touch-dry, and lay up the stack in order, ply 1 at the bottom: rubber, canvas, rubber, ... with the holes lined up over a 24 mm dowel through the middle, and plies 15, 16 and 17 rubber to rubber with no canvas. Press it between boards in clamps overnight. Trim the sides square with the knife and round the edges of the two striking faces slightly.

مواد مورد نیاز این مرحله:

چسب تماسیچسب تماسی1 قطعه

ابزارهای مورد نیاز:

میخ‌های چوب سختمیخ‌های چوب سخت
گیرهٔ میله‌ایگیرهٔ میله‌ای
چاقوی کاردستیچاقوی کاردستی
گونیای ترکیبیگونیای ترکیبی
6

Turn the handle

Turn a hardwood handle 330 mm long. At its head end turn the flared part 2a as long as plies 1 to 15 are thick, 32 mm at the end tapering to 24; then the groove 2b, 20 mm across and as long as plies 16 and 17; then the shoulder 2c, 28 mm, to bear on the head's inner face; then the grip, 28 mm tapering to 26 at its end, so it can pass the eye. Check each diameter with the caliper against the plies.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه

ابزارهای مورد نیاز:

تراش چوبتراش چوب
ست ابزار تراش (HSS)ست ابزار تراش (HSS)
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
عینک ایمنیعینک ایمنی
7

Fit the head

Warm the head for ten minutes in hot water and dry it. Push the grip end of the handle into the eye from the outer face (ply 1) and force it right through, the rib stretching over the grip and the shoulder, until the flared part seats in the eye and the rib snaps into the groove. Let it cool. Strike a board: the head must not move.

ابزارهای مورد نیاز:

آبآب
8

Troubleshooting

Rubber mallet troubleshooting.

Flow

Loading...
9

History and honest limits

**Chauncy P. Whisler** of Kenmore, Ohio, assignor to The Miller Rubber Company, US 1,501,827, dated 15 July 1924, filed 2 January 1924. He claimed "a mallet having a head of elastic material provided with an outwardly flaring handle-receiving eye provided with an annular internal rib adjacent the inner face of the head, and a handle having an outwardly flared end engaging said flared eye, and an annular groove engaged by said annular rib", and "a stepped conical eye". His head was moulded of rubber and fibrous material, as in Maranville and Dabney's application; ours is laminated from rubber sheet and canvas with contact cement. He gives no sizes; every size here is ours.

مواد

4

ابزارهای لازم

11

فایل‌های طراحی

1

این نقشه می‌سازد

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...