همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
Forge

ایجاد شده توسط

Forge

15. نوامبر 2026NO
۷
۰
۰
۰
۰

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)

C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
متوسط
A day

دستورالعمل‌ها

1

The steps

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Willey

"A very efficient, quick-opening and closing vise for the drill-press table."
3

Make the bed

Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.

مواد مورد نیاز این مرحله:

تسمه فولاد نرمتسمه فولاد نرم1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
سنبهٔ نشانه‌گذاریسنبهٔ نشانه‌گذاری
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
4

Make the end supports

Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.

مواد مورد نیاز این مرحله:

تسمه فولاد نرمتسمه فولاد نرم1 قطعه
مجموعهٔ پیچ‌های شش‌گوشمجموعهٔ پیچ‌های شش‌گوش1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
سوهان (سوهان دستی)سوهان (سوهان دستی)
5

Make the fixed jaw

Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.

مواد مورد نیاز این مرحله:

تسمه فولاد نرمتسمه فولاد نرم1 قطعه
میلگرد فولاد نرممیلگرد فولاد نرم1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
سوهان (سوهان دستی)سوهان (سوهان دستی)
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
چکش گِرد‌سرچکش گِرد‌سر
6

Make the sliding jaw

Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.

مواد مورد نیاز این مرحله:

تسمه فولاد نرمتسمه فولاد نرم1 قطعه
میلگرد فولاد نرممیلگرد فولاد نرم1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
سوهان (سوهان دستی)سوهان (سوهان دستی)
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
چکش گِرد‌سرچکش گِرد‌سر
گیرهٔ رومیزیگیرهٔ رومیزی
7

Make the cam

Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.

مواد مورد نیاز این مرحله:

محور فولادیمحور فولادی1 قطعه
میلگرد فولاد نرممیلگرد فولاد نرم1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
دریل ستونیدریل ستونی
مجموعه متهمجموعه مته
چکش گِرد‌سرچکش گِرد‌سر
8

Use it

Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.

مواد مورد نیاز این مرحله:

مجموعهٔ پیچ‌های شش‌گوشمجموعهٔ پیچ‌های شش‌گوش1 قطعه

ابزارهای مورد نیاز:

دریل ستونیدریل ستونی
9

Troubleshooting

Drill vise troubleshooting.

Flow

Loading...
10

History and honest limits

From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.

مواد

4

ابزارهای لازم

7

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...