همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Winding Sticks: a Pair of Parallel Mahogany Strips Planed Together (Work, 1889)
Woody

ایجاد شده توسط

Woody

8. نوامبر 2026NO
۹
۰
۰
۰
۰

Winding Sticks: a Pair of Parallel Mahogany Strips Planed Together (Work, 1889)

Two parallel wooden strips laid across a board to show twist (winding). Carpenters and joiners made their straightedges in pairs as winding strips: if two parallel strips still meet edge to edge when their edges and ends are swapped, three edges have been checked against each other and the strips are true. Straight-grained mahogany is used for strips under three feet. The two are planed together, then tried against each other and reversed until no difference shows. Source: J. H., 'Home-Made Tools', Work, 26 October 1889, pp. 499-500. Picture: Figs. 26-27.
متوسط
Unknown (the stuff is left to stand for days or weeks first)

دستورالعمل‌ها

1

Read the source

"Carpenters, joiners, pattern makers, and cabinet makers usually make their straightedges in pairs as 'winding strips;' and it is clear that if two winding strips are in the first place parallel, and then coincident when the positions of edges and ends are changed, there is obtained really the contact of three edges." (Work, 26 October 1889.)
2

Rough out and let stand

Rough out two strips of well-seasoned, straight-grained mahogany (for strips under three feet; long ones are made of yellow pine). Jack them over and let them stand for a few days or even weeks, because fresh-cut strips curve and warp. Length, width and thickness are not given (unknown).

مواد مورد نیاز این مرحله:

نوارِ چوب سختنوارِ چوب سخت2 mahogany strips

ابزارهای مورد نیاز:

رندهٔ دستیرندهٔ دستی
ابعاد نامعلومابعاد نامعلوم
3

Plane them together

Plane both to gauged thickness and width and square the ends. Screw the two side by side, then finish the edges together with a trying plane sharpened keenly and set very fine. Gauge to width with a fine-toothed gauge, check them parallel with calipers, and keep the edges square to the faces with a try square.

ابزارهای مورد نیاز:

پیچ چوبپیچ چوب
رندهٔ دستیرندهٔ دستی
خط‌کش نشانه‌گذار نجاریخط‌کش نشانه‌گذار نجاری
کولیسکولیس
گونیای ثابتگونیای ثابت
4

Test the edges

To test an edge without a straightedge, lay the strip on a board, scribe a fine line along the edge, turn the strip over and bring the opposite edge to the line: any error shows at twice its size. Plane off the high parts, still checking with calipers and square.

ابزارهای مورد نیاز:

تختهٔ چوب سختتختهٔ چوب سخت
چاقوی خط‌کشیچاقوی خط‌کشی
رندهٔ دستیرندهٔ دستی
کولیسکولیس
گونیای ثابتگونیای ثابت
5

Unfasten and try them against each other

Take the screws out. Lay the strips edge to edge by opposite edges in turn, then change ends and try the opposite edges again, correcting with the trying plane until no difference shows (woodworkers test by chalking the edges and laying them together). Most of the work should already have been done while they were joined.

ابزارهای مورد نیاز:

گچ نشانه‌گذاریگچ نشانه‌گذاری
رندهٔ دستیرندهٔ دستی
کولیسکولیس
گونیای ثابتگونیای ثابت
6

Varnish the faces

Protect the broad faces and the ends with shellac varnish, but not the edges, which are chalked in use. Chalking wears the edges hollow and wood always warps a little, so re-correct winding strips every few months, and keep them for testing winding only.

مواد مورد نیاز این مرحله:

ورنی شلاکیورنی شلاکی1 faces and ends

مواد

2
  • 2 mahogany strips
    جایگزین
  • 1 faces and ends
    جایگزین

ابزارهای لازم

9

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...