همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Workbench: a Pine Bench with a Plank Top and Vise (Boy Mechanic, 1913)
Woody

ایجاد شده توسط

Woody

4. نوامبر 2026NO
۱۲
۰
۰
۰
۰

Workbench: a Pine Bench with a Plank Top and Vise (Boy Mechanic, 1913)

A boy's first workshop bench: two mortised pine leg frames bolted to braces, a 3 1/2 ft top of one 2 x 12 in plank with a back board, a tool rack behind, and a wooden vise on an iron bench screw. Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
متوسط
Unknown

دستورالعمل‌ها

1

Make the two leg frames

Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.

مواد مورد نیاز این مرحله:

الوار کاجالوار کاج1 2 x 4 in: legs, crosspieces

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
اسکنهٔ کام‌تراشیاسکنهٔ کام‌تراشی
چکشچکش
2

Brace them together

Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.

مواد مورد نیاز این مرحله:

الوار کاجالوار کاج1 2 x 4 in: braces
پیچ سرگرد گردن‌چهارگوشپیچ سرگرد گردن‌چهارگوش4 3/8 x 6 in

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
آچار فرانسهآچار فرانسه
3

Fit the plank top

Make the main top M from one 2 x 12 in plank 3 1/2 ft long. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.

مواد مورد نیاز این مرحله:

الوار چوب سختالوار چوب سخت1 2 x 12 in, 3 1/2 ft
تختهٔ کاجتختهٔ کاج1 back board
پیچ چوبپیچ چوب1 long

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
رندهٔ کفیرندهٔ کفی
پیچ‌گوشتی تختپیچ‌گوشتی تخت
4

Add the tool rack

Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.

مواد مورد نیاز این مرحله:

تختهٔ کاجتختهٔ کاج2 7/8 in, 3 1/2 ft
میخمیخ1 قطعه

ابزارهای مورد نیاز:

دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
ارهٔ دستیارهٔ دستی
چکشچکش
5

Fit the vise

Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).

مواد مورد نیاز این مرحله:

الوار کاجالوار کاج1 2 x 6 block, 2 x 4 pieces, guide rails
پیچ میزکار برای منبتپیچ میزکار برای منبت1 قطعه
پیچ سرگرد گردن‌چهارگوشپیچ سرگرد گردن‌چهارگوش1 for L and P
میخمیخ1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
اسکنهٔ کام‌تراشیاسکنهٔ کام‌تراشی
دریل دستهٔ گردان با متهدریل دستهٔ گردان با مته
آچار فرانسهآچار فرانسه
چکشچکش

مواد

7

ابزارهای لازم

7

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...