Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Air Blower: a Hand-Cranked Fan Blow-Bellows for a Portable Forge (Hasluck, 1904)
An air blower gives a fire a steady stream of air. Hasluck's Smiths' Work (1904) shows a small one for a home-made forge: a brass box with a four-winged tin fan on an iron spindle, spun fast by a hand wheel pressing on a rubber-covered roller. Unlike old bellows it blows continuously, through an outlet 2 1/2 in wide and 3/4 in deep.
The book's drawings carry no sizes for the box, so its size, the sheet thickness and the metals of the wire and the plate are unknown here; the tools are ours.
Source: P. N. Hasluck, Smiths' Work (1904), pp. 140-143, Figs. 202-211. Picture: their Figs. 203-204.
Miðlungs
Two days
Leiðbeiningar
1
1
Read Hasluck
Read Hasluck
"When this is all done, turn the handle rapidly; the fan inside will then revolve at a good rate, and a strong draught will be obtained."
2
2
Cut out the box
Cut out the box
Cut the two sides and the bottom of the box from sheet brass, and a piece for the top covering, but do not join them yet. Hasluck gives no sizes for the box (unknown); its outlet is to be 2 1/2 in wide and 3/4 in deep.
Efni fyrir þetta skref:
Messingplata1 sides, bottom and coveringNauðsynleg verkfæri:
Plötuklippur
Óþekkt mál3
3
Make the fan
Make the fan
Make the iron spindle (Figs. 204, 205). Drill two holes in each of its four sides, one at each end, tap them, and screw in pieces of wire about 5/16 in long. Cut four pieces of tin, a little narrower than the box, and punch holes in them to match. Slip each wing over its wires, put a washer over each wire and rivet it over. Five or six wings may be used; then solder pieces of wire between them to stiffen them (Fig. 211).
Efni fyrir þetta skref:
Járnteinn1 spindle
Óþekktur málmur1 wire
Blikkplata1 four wings
Flöt skinna8 stykkiNauðsynleg verkfæri:
Handbor
Snittsett
JárnsögPlötuklippur
Hnoðhamar
Lóðbolti4
4
Fit the spindle and close the box
Fit the spindle and close the box
Screw the brass bearings (Fig. 206), a ring with three spokes and a hole in the middle, to the two sides. Fit the iron spindle in the bearings, screw the sides and bottom together, then screw the covering over the top.
Efni fyrir þetta skref:
Messingplata1 two bearings
Vélskrúfur1 settNauðsynleg verkfæri:
HandborSnittsett5
5
Fit the hand wheel
Fit the hand wheel
The wheel has to be bought. Turn a brass spindle for it (Fig. 207), thread it at each end and fix it with a nut to a plate (Fig. 208); put on the wheel, hold it with a washer and another nut, and fit the knob on rather loosely. Before fixing the wheel, turn a small piece of wood (Fig. 209), put an india-rubber band over it and screw it onto the projecting end of the iron spindle. Fix the wheel so it presses tightly against this roller. Instead, both wheels may be grooved and driven by a band.
Efni fyrir þetta skref:
Handsnúið járnhjól1 stykki
Messingstöng1 wheel spindleÓþekktur málmur1 plate
Sexkantró2 stykkiFlöt skinna1 stykki
Timburborð1 roller
Teygjur1 stykkiNauðsynleg verkfæri:
MálmrennibekkurSnittsettHandbor6
6
Fit the nose-piece
Fit the nose-piece
Cut the nose-piece from sheet brass to the pattern (Fig. 210) and bend it at right angles along the dotted lines so it fits over the outlet end of the box. Rivet or solder its two edges together, drill it and screw it on. Turn the handle quickly to test the draught.
Efni fyrir þetta skref:
Messingplata1 nose-pieceNauðsynleg verkfæri:
PlötuklippurLóðboltiHandbor
Öryggisgleraugu7
7
History and honest limits
History and honest limits
Hasluck's "Home-made Portable Forges" chapter offers this fan as a cheaper, steadier alternative to the old leather bellows, costing about half as much. He adds that gun-metal is better than brass for all parts except the covering and nose-piece.
The drawings carry no sizes, so the box size, the sheet thickness and the metals of the wing wires and wheel plate are unknown; the tools are ours.
Efni
11- 1 nose-pieceStaðgengill
- 1 spindleStaðgengill
- 1 plateStaðgengill
- 1 four wingsStaðgengill
- 9 stykkiStaðgengill
- 1 settStaðgengill
- 1 stykkiStaðgengill
- 1 wheel spindleStaðgengill
- 2 stykkiStaðgengill
- 1 rollerStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
9- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Þessi teikning býr til
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.