Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float.
Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt.
Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
Miðlungs
Unknown
Leiðbeiningar
1
1
Turn the pulleys
Turn the pulleys
Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.
Efni fyrir þetta skref:
Harðviðarborð4 built-up pulleysNauðsynleg verkfæri:
Trérennibekkur2
2
Mount the pulleys
Mount the pulleys
Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.
Efni fyrir þetta skref:
Stálpípa (þykkveggja, með skrúfgangi á endum)3 shafts
Óþekktur málmur1 babbitt bushings
Furutimbur1 frameNauðsynleg verkfæri:
Málmþjöl
Gatasleif
Handsög
Hamar3
3
Make the belt
Make the belt
Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.
Efni fyrir þetta skref:
Sandpappír1 6 in garnet paper
Bómullardúkur1 stykki
Dýralím1 stykkiNauðsynleg verkfæri:
C-þvinga4
4
Set up and run
Set up and run
Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.
Efni fyrir þetta skref:
Furutimbur1 platform, floatNauðsynleg verkfæri:
TrérennibekkurEfni
7- 4 built-up pulleysStaðgengill
- Staðgengill
- 1 babbitt bushingsStaðgengill
- 1 platform, floatStaðgengill
- 1 6 in garnet paperStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Þessi teikning býr til
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.