Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Málmsmíði
791 teikningar tiltækar • 10 undirflokkar
Skoða undirflokka
Teikningar (791)
Sprung-Leg Tubing Cutter: a Bent Rod With a Disk Outside and a Roller Inside, the Handle's Screw Bends One Leg In (Zeiler, 1958)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Slip-Knob Tube Cutter: the Feed Knob Turns the Screw Through Spring-Loaded Plates and Slips Before the Tube Is Crushed (Parker, 1944)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)
eftir Forge
Málmsmíði
0
0
0
0
0
0
V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Four-Edge Chatterless Countersinks: Two Pairs of Edges Set Off the Centre Lines, One Raked Each Way (Manewich, 1946)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Spiral-Edge Countersinks: One Curved Slot Up the Cone Makes an Edge That Slices Instead of Scraping (Laursen, 1926)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Clamp-On Countersink: Two Blocks Screwed Round Any Drill, Twin Cutters Countersink the Hole as It Is Bored (Brackin, 1903)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Cross-Hole Countersinks: A Slanting Hole Through the Cone Makes One Spiral Shearing Lip (Taylor, 1903)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Threaded-Stud Rubber-Head Hammer: Heads Screw Onto the Body's Own Studs and Lock the Handle's Nail In (Dicks, 1951)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Long-Pilot High-Speed Wood Bits: A Flat Plate and a Long Square-Edged Pilot, No Screw Feed (Smith, 1951)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Angled-Side Spade Bits: Each Wing Bent Forwards Along a Diagonal Line, the Way the Bit Turns (Vasudeva, 2005)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Fluted-Shoulder Spade Bits With Spurs: Flutes Along the Shoulders, Stopped by Corner Spurs (Williams & Thackston, 1987)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Diamond-Point Spade Bits: A Thinned, Wide-Angled Point Does More of the Cutting (Southall, 1975)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Fluted-Point Spade Bits: A Groove Down Each Face of the Point Sharpens Its Cutting Edge (Robinson, 1957)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Divisible Flanged Shaft Collar: Two Halves Locked by Lugs, Bolted Through the Shaft in One of Three Hole Pairs (Obey, 1916)
eftir Forge
Málmsmíði
1
0
0
0
0
0
One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)
eftir Forge
Málmsmíði
0
0
0
0
0
0
Injection Moulding Machine: Twin Intermeshing Screws as Plasticiser and Ram (Baigent, US 2,916,769)
eftir Emma
Iðnaður
2
0
0
0
0
0
Sýni 24 af 791