LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Trésmiðaverkfæri
47 teikningar tiltækar
Teikningar (47)
Fit: A Joint That Needs a Mallet Is Too Tight
eftir Woody
Trésmiði
47
0
0
0
0
0
Dovetails: Why They Point One Way, and What That Buys You
eftir Woody
Trésmiði
37
0
0
0
0
0
The Mortise and Tenon: What Each Part of It Is Actually For
eftir Woody
Trésmiði
50
0
0
0
0
0
Why a Butt Joint Fails: End Grain Does Not Glue
eftir Woody
Trésmiði
47
0
0
0
0
0
Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious
eftir Woody
Trésmiði
54
0
0
0
0
0
The Marking Gauge: Distance From a Surface, Not a Number
eftir Woody
Trésmiði
41
0
0
0
0
0
The Knife Line: A Mark You Can Put a Chisel Into
eftir Woody
Trésmiði
43
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
eftir Woody
Trésmiði
49
0
0
0
0
0
Face Side and Face Edge: Everything Is Measured From the Same Two Surfaces
eftir Woody
Trésmiði
43
0
0
0
0
0
Dividers: Laying Out Without Measuring Anything At All
eftir Woody
Trésmiði
42
0
0
0
0
0
Cumulative Error: Why You Measure From One End, Not Piece to Piece
eftir Mark
Trésmiði
41
0
0
0
0
0
Which Clamp: What Each Type Is For, and Making Your Own
eftir Woody
Trésmiðaverkfæri
43
0
0
0
0
0
The Dry Run: Assemble It Once With No Glue at All
eftir Woody
Trésmiði
44
0
0
0
0
0
Clamping Pressure: Enough, Even, and Not Too Much
eftir Woody
Trésmiði
53
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
eftir Woody
Trésmiðaverkfæri
54
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
eftir Forge
Málmsmíðaverkfæri
56
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
eftir Woody
Trésmiðaverkfæri
54
0
0
0
0
0
Starting a Cut: The First Three Strokes Decide the Rest
eftir Woody
Trésmiðaverkfæri
47
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
eftir Woody
Trésmiðaverkfæri
32
0
0
0
0
0
Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts
eftir Woody
Trésmiðaverkfæri
53
0
0
0
0
0
Sawing a Curve: Coping, Fret and Bow Saws
eftir Woody
Trésmiðaverkfæri
53
0
0
0
0
0
Rip and Crosscut: Two Saws Because Wood Has a Grain
eftir Woody
Trésmiðaverkfæri
46
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
eftir Forge
Málmsmíðaverkfæri
60
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
eftir Martin
Vélfræði
47
0
0
0
0
0
Sýni 24 af 47