Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Three-Series Beater Churn: Outer and Inner Loops Turn One Way, the Middle Loops and Centre Blades the Other
Simon G. Cheever of Boston received US 28,560, dated 5 June 1860, for a machine for mixing paints, oils and powders that "may also be used as a butter mill or churn". Three nested series of loop beaters hang on one shaft: the outer and inner series turn one way and the middle series the other, while curved blades at the centre throw the cream outward into them. One crank drives it all through a wheel with a pinion on each side.
This builds it as a churn. The patent gives no sizes; every size here is ours.
Lengra kominn
About 2 days, plus printing
Leiðbeiningar
1
1
Three series, two directions
Three series, two directions
Hleð Jupyter-vinnubók…
2
2
Nested dashers driven by one wheel and two pinions, seven weeks before
Nested dashers driven by one wheel and two pinions, seven weeks before
Dunham and Hipple nest two frames. Cheever nests three, the middle one turning against the other two.
3
3
Read US 28,560
Read US 28,560
"... the arrangement of the pinions on opposite sides of the driving wheel, and their connections through the collars with the outer and inner series of beaters or mixers, and the action of the central curved blades, is to throw the material constantly from the center to the circumference and there to submit it to the opposing forces of the beaters revolving in opposite directions."
4
4
Print the driving wheel C
Print the driving wheel C
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion D
Print the pinion D
Spur pinion, 16 teeth, module 2, with a hub; bored 12.4 mm for the shaft F. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the pinion E
Print the pinion E
Spur pinion, 16 teeth, module 2, with a hub; bored 18.4 mm for the sleeve of collar G. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Outer and inner series I, I on collars G and H2
Outer and inner series I, I on collars G and H2
Bend 6 mm stainless rod into two outer loops 220 mm across and 300 tall and two inner loops 120 across and 220 tall, open at the middle of top and bottom. Cut 130 mm of 18 mm stainless tube as the sleeve of collar G and fix two printed or hardwood hubs 32 mm across on it, 40 mm apart; screw the outer loops' top ends to the upper hub and the inner loops' to the lower, crossed at right angles. Screw their bottom ends to two hubs H2 bored 12.6 mm, which turn free on the shaft.
Efni fyrir þetta skref:
Stöng úr ryðfríu stáli4 stykki
Rör úr ryðfríu stáli1 stykki
Harðviðarborð1 stykki
Vélskrúfur16 stykki
PETG-þráður1 stykkiNauðsynleg verkfæri:
FDM-þrívíddarprentari
Skrúfstykki
Járnsög
Þjalir (handþjöl)
Hleðslubor
Borasett
Skrúfjárnasett8
8
Middle series h, collars H and G2, blades L and M
Middle series h, collars H and G2, blades L and M
Bend two middle loops 170 mm across and 260 tall. Screw their top ends to a ring H 44 mm across, bored 18.6 mm, that rides on the sleeve between G's two hubs, and their bottom ends to a hub G2 pinned to the shaft F between the two H2 hubs, set 45 degrees from the outer loops. Pin two curved printed blades, 180 tall and reaching 50 mm, on the shaft inside the inner loops.
Efni fyrir þetta skref:
Stöng úr ryðfríu stáli2 stykkiVélskrúfur8 stykki
Splitti3 stykkiPETG-þráður1 stykkiNauðsynleg verkfæri:
SkrúfstykkiJárnsögÞjalir (handþjöl)HleðsluborBorasettSkrúfjárnasett9
9
Shaft F, bridge, arm A, wheel C and crank K
Shaft F, bridge, arm A, wheel C and crank K
Pass a 12 mm stainless shaft F, 500 mm long, up through G2, H2 and the sleeve. Cut a hardwood bridge 350 x 330 x 15 mm to lie on the bucket's rim, bored 24 mm in the middle for the sleeve. Fix the pinion E on the sleeve's top, and the pinion D on the shaft above it. Screw two hardwood arms to the bridge carrying a 12 mm stainless axle with the wheel C meshing E below and D above, and a crank K on its end; a hardwood bracket over D holds the shaft's top.
Efni fyrir þetta skref:
Stöng úr ryðfríu stáli2 stykkiHarðviðarborð2 stykki
Harðviðartappar1 stykki
Trélím1 stykki
Tréskrúfur10 stykki
Shaft Collar4 stykkiPETG-þráður1 stykkiNauðsynleg verkfæri:
Borðsög
Spaðabora-settHleðsluborBorasettJárnsög
StangarþvingaSkrúfjárnasett
Málband10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the outer and inner loops on collar G and the H2 hubs, the middle loops on collar H and G2, the central blades, and on the bridge the wheel C with pinion E below and D above.
11
11
Churn
Churn
Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, lower the beaters in and set the bridge on the rim. Turn the crank steadily, timing it. When the butter comes, lift the bridge and beaters out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Efni fyrir þetta skref:
Rjómi8 l
Gróft sjávarsalt1 stykki
Vatn1 stykkiNauðsynleg verkfæri:
Hitamælir með nema sem situr í
Skeiðklukka
Stafræn eldhúsvog
Stór hrærskál úr ryðfríu stáli12
12
Troubleshooting
Troubleshooting
Three-series beater churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Simon G. Cheever** of Boston, US 28,560, 5 June 1860, "Machine for Mixing Paints". He did not claim opposed pinions on one wheel, nor mixers or churn dashers turning oppositely, but the arrangement of the collars so the middle series turns against the outer and inner, with the central curved blades. His arm is metal and clamps into a dovetail socket on any bench; ours is hardwood on a bridge across the bucket. He leaves the number and shape of the beaters open; our loops, counts and every size are ours.
Efni
13- 4 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2 stykkiStaðgengill
- 24 stykkiStaðgengill
- 3 stykkiStaðgengill
- 3 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 10 stykkiStaðgengill
- 4 stykkiStaðgengill
- 8 lStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
15- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
4Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
Nested Hollow-Dasher Churn: Two Dasher Frames Turn Contrary Ways, Their Hollowed Side Pieces Driving Cream at Webs
eftir Buttercup
Trésmiði
0
0
0
0
0
0
Interlapping Spiral-Dasher Churn: Two Upright Shafts With Arms Set in Screw Form Interlap, One Turning the Other
eftir Buttercup
Trésmiði
0
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
eftir TheChef
HANDVERK
60
0
0
0
0
0
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.