LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Closed-Globe Egg Beater: Concentric Rings in a Shut Sphere
James M. Jay, Canton, Ohio · Public domain (expired patent)
Martin

Búin til af

Martin

6. október 2026NO
21
0
0
0
0

Closed-Globe Egg Beater: Concentric Rings in a Shut Sphere

Beaten in an open bowl, egg spatters and the air is not forced into it. James M. Jay of Canton, Ohio, received US 27,054, dated 7 February 1860, for an egg beater whose case is a hollow globe of two halves hinged and caught together; a horizontal shaft through it carries concentric rings, the outer one close to the inside so it sweeps the bottom, turned by a wheel and gear on a stand. "The air which occupies the upper part ... is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs." This rung works out the air-to-egg ratio, then prints the ring dasher and gears, closes it in two bowls, and times a beating.
Miðlungs
About 5 hours, plus printing

Leiðbeiningar

1

Air shut in with the eggs

Hleð Jupyter-vinnubók…
2

A dasher in a closed box before it

The embedded blueprint spins a dasher in a square box. Jay shuts the eggs in a globe so the air is driven into them.
3

Read US 27,054

"In my egg beater the air which occupies the upper part of the hollow bottom B, together with that which fills the cover or cap C, is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs by the rings or dashes H', while the eggs are carried up and through the air in the cap or case C, so that a perfect mixture of the air and eggs is effected."
4

Print the rings and gears

Print the concentric-ring dasher, the 36-tooth wheel and the 12-tooth gear. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

Efni fyrir þetta skref:

PETG-þráðurPETG-þráður1 stykki

Nauðsynleg verkfæri:

FDM-þrívíddarprentariFDM-þrívíddarprentari
5

Print the concentric-ring dasher

The concentric-ring dasher, printed as step 4 describes.
HönnunarskráSTLCC0 - Free
Sækja líkan
6

Print the 36-tooth wheel

The 36-tooth wheel, printed as step 4 describes.
HönnunarskráSTLCC0 - Free
Sækja líkan
7

Print the 12-tooth gear

The 12-tooth gear, printed as step 4 describes.
HönnunarskráSTLCC0 - Free
Sækja líkan
8

Make the globe

Take two matching bowls 120 mm across from the set. Drill both rims at opposite points for the shaft, 5.5 mm, so the shaft lies on the joint.

Nauðsynleg verkfæri:

HleðsluborHleðslubor
BorasettBorasett
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
HrærskálasettHrærskálasett
9

Shaft, rings and stand

Pass a 5 mm rod through one bowl's holes and the dasher's hub, and epoxy the hub at the centre. Epoxy the 12-tooth gear on the rod outside. Mount the 36-tooth wheel with a crank on an M5 screw on a hardwood upright so it meshes, and stand the lower bowl in a plywood ring.

Efni fyrir þetta skref:

Kringlótt stöng úr deigu stáliKringlótt stöng úr deigu stáli1 stykki
Tveggja þátta epoxýTveggja þátta epoxý1 stykki
HarðviðarkubburHarðviðarkubbur1 stykki
KrossviðarplataKrossviðarplata1 stykki
VélskrúfurVélskrúfur1 stykki
Flöt skinnaFlöt skinna1 stykki
SexkantróSexkantró1 stykki
Tréskrúfa #8 x 1"Tréskrúfa #8 x 1"1 stykki

Nauðsynleg verkfæri:

JárnsögJárnsög
LaufsögLaufsög
HleðsluborHleðslubor
BorasettBorasett
SkiptilykillSkiptilykill
SkrúfjárnasettSkrúfjárnasett
10

The patent drawing

US 27,054 drawing sheet, public domain (expired patent).
Skref 10 - Image 1
11

Closed against open

Beat two egg whites with the top bowl clamped on and time them to stiff peaks; then again with the top off. Compare the times and the volume of foam.
Skref 11 - Image 1

Efni fyrir þetta skref:

EggEgg4 stykki

Nauðsynleg verkfæri:

SkeiðklukkaSkeiðklukka
Stafræn eldhúsvogStafræn eldhúsvog
12

A globe that leaks, rings that scrape

Closed-globe egg beater troubleshooting.

Flow

Loading...
13

History and honest limits

**James M. Jay** of Canton, Ohio, assignor to himself and John Danner, received US 27,054, dated 7 February 1860. The halves are turned to break joints and fit tight; a hook on the cover hangs on a pivot between lugs, and a swinging catch holds the cover down; the shaft's bearings are in the lower half's edge, the cover cut to fit over them. He wrote that it does not matter whether one or more eggs are beaten. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Two bought bowls stand in for his turned halves, without a hinge. Your times are the result.

Efni

10

Nauðsynleg verkfæri

11

Hönnunarskrár

3

Þessi teikning býr til

Thumbnail
Tímabundinn texti

Sveifarþeytari

Free

9
0

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways

eftir MartinNO

MATUR OG DRYKKUR

34
0
0
0
0
0
Stepped Spiral Egg Beater: A Stepped Dasher Spun in a Square Box

Stepped Spiral Egg Beater: A Stepped Dasher Spun in a Square Box

eftir MartinNO

MATUR OG DRYKKUR

26
0
0
0
0
0
Gear Trains: Idlers, Compounding and Hitting a Given Ratio

Gear Trains: Idlers, Compounding and Hitting a Given Ratio

eftir MartinNO

Vélfræði

46
0
0
0
0
0

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...