Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI

Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
Ferdinand H. Dalrymple of Bedford, Ohio, received US 2,163,315, dated 20 June 1939, for a shaft collar "comprised of few parts which are readily obtainable as standard market articles". Two washers are held apart by nuts welded between them. The nuts' inner faces rest on the shaft, and a set screw in one nut's thread holds it. It needs no machining. He says it is stronger, lighter and cheaper than a cast collar, and breaks less readily under a hammer. It also touches the shaft only along lines, so it rusts to it less, and oil can be put in between the nuts.
The patent gives no sizes for this form; every size here is ours.
Byrjandi
About 1 hour
Leiðbeiningar
1
1
Will it fit together?
Will it fit together?
Hleð Jupyter-vinnubók…
2
2
Read US 2,163,315
Read US 2,163,315
"Preferably, I use as plates standard washers of suitable dimension, and I use as blocks standard nuts."
"Inasmuch as the space between the plates is not sufficient for the convenient manipulation of an ordinary wrench, I use socketed set screws for securing the collar to the shaft."
3
3
Set the parts up on a bar
Set the parts up on a bar
Use plain steel washers and nuts, not zinc-plated ones. Wire-brush them clean. Grip a 16 mm round bar upright in the vice. Slide one washer onto it, stand four M8 nuts on the washer round the bar at quarter turns, each with a flat down and its hole pointing at the bar's centre and its inner face against the bar. Put the second washer on top and squeeze the stack with the C-clamp; check with the square that the washers are parallel.
Efni fyrir þetta skref:
Flöt skinna2 stykki
Sexkantró4 stykkiNauðsynleg verkfæri:
Sívöl stöng úr mjúku stáli
Skrúfstykki
C-þvinga
Vírburstasett
Fjölvinkill
Stafrænn skífmælir 6 tommur4
4
Weld the nuts to the washers
Weld the nuts to the washers
Wearing the helmet and gloves, tack each nut to both washers with a short fillet weld at its outer corner, keeping the arc away from the bar. Let it cool, lift the collar off the bar, and run a fillet along both ends of every nut on both washers. Chip and wire-brush the slag. Run the set screw in and out of one nut to clear any spatter from its thread, and file the bore ends smooth.
Efni fyrir þetta skref:
Suðurafskaut4 stykkiNauðsynleg verkfæri:
Ljósbogasuðuvél
Sjálfdökknandi suðuhjálmur
Suðuhanskar
Vírburstasett
Vinkilslípirokkur
Þjalasett
Öryggisgleraugu5
5
The collar in 3D
The collar in 3D
FreeCAD model, our sizes: the two 50 mm washers, the four M8 nuts between them at quarter turns, their inner faces on a 16 mm shaft, and the socket set screw in one nut. The welds are not modelled.
6
6
Fit it on the shaft
Fit it on the shaft
Run an M8 x 8 cup point socket set screw into one nut from outside. Slide the collar onto the shaft to its place and tighten the screw with the hex key between the washers. Try to slide and turn it; it must not move.
Efni fyrir þetta skref:
Skrúfa með skálarodda1 stykkiNauðsynleg verkfæri:
Sexkantlyklasett7
7
Troubleshooting
Troubleshooting
Built-up collar troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
**Ferdinand H. Dalrymple** of Bedford, Ohio, US 2,163,315, dated 20 June 1939, filed 2 November 1937. He claimed "opposed spaced plane plates formed with coaxial bores for the reception of a shaft, transverse spaced internally-threaded blocks welded to the opposed faces of the plates and serving as the sole means for holding the plates in relatively fixed positions, and set screws engaging the blocks". His Figs. 8 and 9 use standard square nuts and socketed set screws; we use hex nuts, as his Figs. 1-5 allow "standard nuts". His patent also shows special blocks, flanged plates, three-plate and split forms; we build the simplest. He gives no sizes for this form; every size here is ours.
Efni
4- 2 stykkiStaðgengill
- 4 stykkiStaðgengill
- 4 stykkiStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
13- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Vinkilslípirokkur3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
1Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.


