Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)
An automatic electric kettle boils water with an immersion heater and switches itself off. J. C. Taylor (US 4,358,666, 1982) mounts one control on the heater's head: a bimetal disc touching the hot head cuts the power if the kettle is switched on dry, and a second bimetal disc in the steam trips an over-centre lever that cuts it when the water boils.
In his kettle (Fig. 14) the steam leaves through a hole high in the wall and runs down a passage between the handle and the wall to the control. A knob resets it.
Source: J. C. Taylor, US Patent 4,358,666 (filed 1980, granted 1982). Picture: its Fig. 14.
Lengra kominn
Unknown
Leiðbeiningar
1
1
Read Taylor
Read Taylor
"The effect is that when the water boils, the lever 16 is tripped by the actuator 22 from its first to its second position, thus interrupting the supply of electricity to the heating element."
2
2
Fit the immersion heater
Fit the immersion heater
Make the kettle body with a spout, lid and handle, an opening low in the back wall for the heater head and a hole high in the wall under the handle for steam. Fix the immersion heater's head watertight in the low opening, with its element low in the kettle and its hot return brazed to the head so the head heats up if the element runs dry. Form a steam passage between the handle and the wall from the high hole down to the head. Body material, size and heater rating are not given.
Efni fyrir þetta skref:
Óþekktur málmur1 kettle body
Hitaelement1 immersion heaterNauðsynleg verkfæri:
Harðlóðunarbrennari
Súlubor
Borasett
Óþekkt mótunaraðferð
Óþekkt mál3
3
Build the switch-on-dry unit
Build the switch-on-dry unit
On the head mount a switch unit with three pins (line, neutral and earth) for the kettle lead's socket. Wire the line pin to one cold end of the element through a movable contact on a springy conductive strip and a fixed contact. Rivet the tongue of a snap-acting bimetal disc to a pillar so its body touches the head. Fit a sliding link that the disc pushes: at about 120 °C (Taylor: "say 120° C.") the disc snaps over and the link parts the contacts.
Efni fyrir þetta skref:
Óþekkt einangrunarefni1 switch unit bodyÓþekktur málmur1 pins, contacts and strip
Tvímálmsræma1 dry-switch discNauðsynleg verkfæri:
SúluborBorasett4
4
Make the steam unit
Make the steam unit
Press a disc of sheet bimetal into a domed die, with a cut-out that leaves a tongue in the middle, so it snaps over when steam heats it. Mount it by its rim on a lever that rocks on two knife edges in notches of a body seated over the switch unit, held by two over-centre C-springs, with a shroud round the pins and a steam opening sealed by an O-ring. A finger of the lever passes through the sliding link; a knob on the lever comes out through the housing. The trip temperature and bimetal grade are not given.
Efni fyrir þetta skref:
Tvímálmsræma1 steam discÓþekkt einangrunarefni1 steam unit body and lever
Gormur2 C-springs
O-hringur1 stykkiNauðsynleg verkfæri:
Óþekkt mótunaraðferð5
5
Close up and use
Close up and use
Screw the outer housing over both units into the threaded pillars, the knob through its opening and the steam passage meeting the steam unit's channel. Fill, plug in the lead and press the knob down to close the contacts. When the water boils, steam reaches the disc, the lever snaps over and the power goes off; switched on dry, the head heats and the other disc cuts it and holds the lever off. Press the knob to reset.
Efni fyrir þetta skref:
Óþekkt einangrunarefni1 outer housing
Sveigjanleg snúra með kló1 kettle lead with socketEfni
7- 1 pins, contacts and stripStaðgengill
- 1 immersion heaterStaðgengill
- 1 outer housingStaðgengill
- 1 steam discStaðgengill
- 2 C-springsStaðgengill
- 1 stykkiStaðgengill
- 1 kettle lead with socketStaðgengill
Þessi teikning býr til
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.