LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Búin til af

Penny

14. október 2026DK
23
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Miðlungs
Two to three days

Leiðbeiningar

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Efni fyrir þetta skref:

Flatt verkfærastálFlatt verkfærastál1 stykki

Nauðsynleg verkfæri:

MálmþjölMálmþjöl
HandborHandbor
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
SmiðjueldstæðiSmiðjueldstæði
HerslufataHerslufata
ÖryggisglerauguÖryggisgleraugu
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Efni fyrir þetta skref:

HarðviðarlistiHarðviðarlisti2 stykki
Kringlótt stöng úr deigu stáliKringlótt stöng úr deigu stáli0.3 m

Nauðsynleg verkfæri:

MálmþjölMálmþjöl
SmiðjueldstæðiSmiðjueldstæði
HerslufataHerslufata
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Efni fyrir þetta skref:

MessingplataMessingplata1 stykki
Vaxaður hörþráðurVaxaður hörþráður3 m

Nauðsynleg verkfæri:

PlötuklippurPlötuklippur
HandborHandbor
MálmþjölMálmþjöl
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Nauðsynleg verkfæri:

MálmþjölMálmþjöl
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Efni fyrir þetta skref:

MessinghleifurMessinghleifur2 kg
ViðarkolViðarkol1 as required
MótasandurMótasandur5 kg

Nauðsynleg verkfæri:

SmiðjueldstæðiSmiðjueldstæði
Deigla úr eldföstum leirDeigla úr eldföstum leir
DeiglutöngDeiglutöng
Mótkassi (efri og neðri)Mótkassi (efri og neðri)
SuðuhanskarSuðuhanskar
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Efni fyrir þetta skref:

VatnVatn1 lítri

Nauðsynleg verkfæri:

MæliglasMæliglas
MálmþjölMálmþjöl
7

A binary set of weights

Hleð Jupyter-vinnubók…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Efni

9

Nauðsynleg verkfæri

12

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...