Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Four-Edge Chatterless Countersinks: Two Pairs of Edges Set Off the Centre Lines, One Raked Each Way (Manewich, 1946)
Joseph J. Manewich of Longmeadow, Massachusetts, received US 2,401,307, dated 4 June 1946, for a countersink that does not chatter. Four teeth are gashed in the cone. The inner ends of one pair of edges sit just ahead of a line through the centre, with their faces raked back. The other pair sit just behind a line at right angles, raked forwards. The edges keep changing how they meet the work as the tool goes in, and each steadies the one opposite, so it can run faster and leaves round, smooth countersinks.
We make a set of three in tool steel. The patent gives no sizes or angles; ours are stated.
Lengra kominn
About 1 day
Leiðbeiningar
1
1
Why the edges are set off the centre lines
Why the edges are set off the centre lines
Hleð Jupyter-vinnubók…
2
2
Read US 2,401,307
Read US 2,401,307
"It has been found that the countersink tool by reason of its novel construction and arrangement may be operated at a higher speed than may those of the prior art while at the same time objectionable chatter is eliminated."
3
3
Turn the blanks
Turn the blanks
From octagonal tool steel turn three blanks: a 90 degree cone to a point, 12, 16 and 20 mm across, a short body 4 and an 8 mm shank 6 50 mm long with three filed flats. Heat each to a cherry red and let it cool slowly in the air.
Efni fyrir þetta skref:
Áttstrent verkfærastál2 stykkiNauðsynleg verkfæri:
Málmrennibekkur
Þríkjálka rennibekkspatróna
Rennibekkjarstál
Fráskurðarjárn
Gráðubogi
Stafrænn skífmælir 6 tommur
Þjalasett
Aflinn
Smiðjutöng
Öryggisgleraugu4
4
Mark and gash the four teeth 8
Mark and gash the four teeth 8
Blue the cone and scribe two diameters across its end at right angles. Mark the positive pair's edges 10 parallel to the first diameter, 0.5 mm ahead of it in the direction of turning, and the negative pair's edges 12 parallel to the second, 0.5 mm behind it. File or grind a gash 11 ahead of each edge, down the cone: for the edges 10 the face raked back about 8 degrees (positive), for the edges 12 raked forward about 5 degrees (negative). Give each edge a little clearance behind it.
Nauðsynleg verkfæri:
Nálaþjalasett
VélskrúfstykkiÞjalasett
BekkslípivélGráðubogi5
5
Harden and temper
Harden and temper
Heat each head to a cherry red, until a magnet no longer sticks, and quench it point first in water, moving it about. Rub it bright with a stone, heat the shank gently 20 mm behind the head, and quench again as soon as a light straw colour reaches the cutting edges.
Nauðsynleg verkfæri:
AflinnSmiðjutöng
Lítill segull
Herslufata
Vatn
Brýni
SuðuhanskarÖryggisgleraugu6
6
Hone and test
Hone and test
Hone all four edges lightly with the stone. Countersink holes in hardwood and in a scrap of aluminium at a higher speed than usual: the cone should be round and smooth, with no chatter marks.
Nauðsynleg verkfæri:
Brýni
Hleðslubor
Borasett
HarðviðarborðÖryggisgleraugu7
7
Troubleshooting
Troubleshooting
Four-edge countersink troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
**Joseph J. Manewich** of Longmeadow, Massachusetts, US 2,401,307, dated 4 June 1946, filed 23 August 1944. He claimed cutting edges in two pairs, "the innermost portions of the cutting edges of one pair thereof disposed adjacent said longitudinal axis and forwardly" of a plane through it, and those of the other pair "rearwardly" of another plane at right angles. He calls the first positive edges with positive rake and the second negative with negative rake. He gives no sizes, offsets or angles; ours are stated, with the house hardening.
Efni
1- 2 stykkiStaðgengill
Nauðsynleg verkfæri
21- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.