LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
GRÆN FRAMTÍÐ
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Building a Newcomen Atmospheric Engine — The First Engine to Do Real Work
Dwalin

Búin til af

Dwalin

25. júní 2026US
2
0
0
0
0

Building a Newcomen Atmospheric Engine — The First Engine to Do Real Work

In 1712 Thomas Newcomen built a machine that changed the world quietly, by pumping water out of coal mines. It was the first engine to turn the heat of a fire into useful mechanical work on a large scale, and every steam engine and motor that followed descends from it.

Its genius is counter-intuitive: the steam does not push the piston. Newcomen's engine fills a cylinder with low-pressure steam, then sprays in cold water to condense that steam into a few drops, leaving a vacuum. The ordinary pressure of the atmosphere — about a tonne on a large piston — then shoves the piston down into the vacuum. That downward stroke rocks a great wooden beam whose far end lifts the mine pump. Because air pressure does the work, it is called an atmospheric engine.

It was thirsty and wasteful, reheating its whole cylinder every stroke, but it was tireless and it worked. For sixty years Newcomen engines drained the mines that supplied the coal that fed the Industrial Revolution — until James Watt's separate condenser made the steam engine efficient enough to drive factories and locomotives.

Lengra kominn
A major build; weeks of fabrication and erection

Leiðbeiningar

1

Grasp the atmospheric principle

Understand the trick before building: the engine works by vacuum, not pressure. Steam fills the cylinder, then is condensed to a vacuum, and the weight of the atmosphere pushes the piston down. The power comes from air pressure, which is why it is called an atmospheric engine.
2

Build the boiler

Build a large domed boiler — historically called a haystack boiler — set over a coal fire. It only needs to raise steam at little more than atmospheric pressure, so it can be a big riveted copper or iron kettle rather than a high-pressure vessel.

Efni fyrir þetta skref:

Sheet CopperSheet Copper40 kg
FirebrickFirebrick120 piece
3

Cast and bore the cylinder

Make a large vertical cylinder, open at the top, of cast brass or iron, and bore it as true as you can. A close-fitting piston runs in it; the better the fit, the less vacuum leaks past. Newcomen sealed the gap with a little water and a leather flap on the piston.

Efni fyrir þetta skref:

Cast Iron CylinderCast Iron Cylinder1 piece
LeatherLeather2 sqm
4

Erect the great beam

Raise a massive timber beam pivoted in the middle on a sturdy wall, like a giant see-saw. Chain one end to the piston by an arch-head, and the other end to the heavy mine pump rod, which also acts as the counterweight that pulls the piston back up.

Efni fyrir þetta skref:

Timber BeamTimber Beam1 piece
5

Plumb the steam and water pipes

Run a steam pipe with a valve from the boiler into the base of the cylinder. Add an injection pipe to spray cold water into the cylinder, and an eduction pipe to drain the condensed water and air away to a well below.

Efni fyrir þetta skref:

Copper TubingCopper Tubing6 meter

Nauðsynleg verkfæri:

WrenchWrench
6

Raise steam

Light the coal fire and bring the boiler to a gentle boil, raising low-pressure steam. Let the engine warm through — the first strokes are weak until the cylinder and pipes are hot and the air is swept out.

Efni fyrir þetta skref:

Bituminous CoalBituminous Coal50 kg
7

Admit steam and let the piston rise

Open the steam valve so steam fills the cylinder under the piston. With little pressure resisting it, the heavy pump rod on the far end of the beam sinks and pulls the piston up to the top of its stroke, filling the cylinder with steam.

Nauðsynleg verkfæri:

Steam ValveSteam Valve
8

Inject cold water to make the vacuum

Shut the steam valve and open the injection jet, spraying cold water into the steam-filled cylinder. The steam collapses into a few drops of water, and the cylinder is left nearly empty — a vacuum beneath the piston.

Nauðsynleg verkfæri:

Steam ValveSteam Valve
9

Take the power stroke

With a vacuum below and open air above, atmospheric pressure drives the piston down hard. This is the working stroke: it rocks the beam, lifts the pump rod at the far end, and raises a column of mine water. All the engine's useful work happens here.

Efni fyrir þetta skref:

WaterWater30 liter
10

Drain and repeat

Drain the warm condensate down the eduction pipe, then re-admit steam to start again. A working Newcomen engine settles into a steady rhythm of perhaps ten to fifteen strokes a minute, pumping day and night.

Nauðsynleg verkfæri:

Steam ValveSteam Valve
11

Make it self-acting

Hang a plug rod from the beam that trips the steam and injection valves automatically at the top and bottom of each stroke. With this linkage the engine works itself, needing only stoking and watching rather than a hand on the valves.

Nauðsynleg verkfæri:

WrenchWrench
12

Know its power and its flaw

The engine will pump a deep mine tirelessly, but it wastes most of its coal reheating the cylinder it just cooled every stroke. Recognising that waste is what led James Watt to add a separate condenser — the next great step in the steam age.

Efni

8

Nauðsynleg verkfæri

2

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

Building an Aeolipile — Hero's Steam-Powered Spinning Sphereeftir Penny
Cartwright's Power Loom — Mechanized Weaving by Steam and Watereftir Tex

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...