Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Oven Thermometer: Door-Mounted Dial with a Curved Bimetal Strip (Whittier, US 1,498,413, 1924)
A dial thermometer that fits in an oven door or wall. Behind an enamelled dial plate, a curved bimetal strip runs from a fixed stud to a little arm on a spindle; as the oven heats, the strip bends, turns the spindle and swings the pointer across the scale on the front. Everything is mounted on the dial plate as one unit and dropped into a shallow stamped case with a glass cap.
Result: a compact oven thermometer, easy to calibrate and adjust.
Source: H. R. Whittier, US 1,498,413 (1924). Unknown: metals, sizes and the scale unit. Picture: the patent drawing.
Miðlungs
Unknown
Leiðbeiningar
1
1
Make the dial unit
Make the dial unit
Cut a metal disk for the dial plate, enamel its front and mark the scale (the patent's drawing reads 200 to 500). Thread a sleeve through the plate near one edge and pass a spindle loosely through it, with a pointer fixed on its front end and a short arm on its back end. Set a stud through the plate: in front it stops the pointer, behind it anchors one end of a curved bimetal strip whose other end is pinned to the arm. Not given: metals, sizes, the scale unit.
Efni fyrir þetta skref:
Óþekktur málmur1 dial plate, sleeve, spindle, pointer, arm, stud
Óþekktur efniviður1 enamel and scale
Tvímálmsræma1 curved stripNauðsynleg verkfæri:
Snittsett
Kringlunefjatöng
Óþekkt mál2
2
Make the case
Make the case
Stamp a shallow case from thin sheet metal, closed at the back, with perforated ears for fixing it in the oven door or wall, and press lugs in from its wall for the dial plate to sit on. Make a cap with a glass to close the open front. Ours: steel sheet and a watch glass.
Efni fyrir þetta skref:
Plata úr mjúku stáli1 case and cap
Úrgler1 windowNauðsynleg verkfæri:
PlötuklippurÓþekkt mál3
3
Assemble, calibrate and fit
Assemble, calibrate and fit
Calibrate the strip and set the pointer while the unit is out of the case, then drop the dial unit onto the lugs and fit the cap, which holds the plate in place. Fasten the case through its ears in the oven door or wall. As the oven heats, the strip bends and the pointer swings across the scale. Not given: how it is calibrated.
Nauðsynleg verkfæri:
BakarofnKringlunefjatöngEfni
5- 1 dial plate, sleeve, spindle, pointer, arm, studStaðgengill
- 1 enamel and scaleStaðgengill
- 1 curved stripStaðgengill
- 1 case and capStaðgengill
- 1 windowStaðgengill
Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.