LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Pop Rivets: Copper Hollow Rivet on a Steel Break Mandrel with a Ring-Cutter Head (Kraemer, US 3,257,890)
A blind rivet set from one side. Kraemer's mandrel head has a sharp ring edge that shears the inner part of the rivet's tail and pushes it into the bore, while the outer part folds round the head. The pull needed is about half, and the set rivet is about as strong in shear as a solid one.
Result: copper pop rivets, 3, 4 or 5 mm, each on its steel mandrel.
Source: Kraemer, US 3,257,890 (1966). His other rivet metals, aluminium-magnesium and 80/20 copper-nickel, are separate compositions. Not given: die design. Picture drawn by Youblob.
Lengra kominn
Factory process
Leiðbeiningar
1
1
Stamp the copper rivet
Stamp the copper rivet
Form a hollow rivet with a flange (set head) at one end and a straight bore. Kraemer says the parts can be made e.g. by stamping. Sizes (mm), outside / bore: 5 / 3, 4 / 2.6, 3 / 1.8. Ours: from copper sheet.
Efni fyrir þetta skref:
Koparplata1 as requiredNauðsynleg verkfæri:
Stönsunarpressa2
2
Form the steel mandrel
Form the steel mandrel
Shape a steel mandrel: draw shaft, a groove as the breaking point, a cone tapering up to the bore size, and a near-hemispherical button head. Head edge diameter (mm): 4.3, 3.6, 2.6 for the 5, 4, 3 mm rivets, so it covers 55-70 % of the rivet's end face. Ours: from steel wire.
Efni fyrir þetta skref:
Stálvír1 as requiredNauðsynleg verkfæri:
Stönsunarpressa3
3
Assemble and size for the work
Assemble and size for the work
Push the mandrel fully into the rivet; it is supplied this way. Pick a length that sticks out past the sheets by 3-5 mm (5 mm rivet), 2.5-3.5 mm (4 mm) or 2-4 mm (3 mm).
Nauðsynleg verkfæri:
Poppnaglabyssusett4
4
Set it from one side
Set it from one side
Put the rivet in the hole, grip the draw shaft and press the tool's head on the flange while pulling. The ring edge shears the tail, the rest bulges and folds round the button head, and the mandrel breaks at its groove.
Nauðsynleg verkfæri:
PoppnaglabyssusettNauðsynleg verkfæri
2- Staðgengill
- Staðgengill
Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.