LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Potentiometer: Podolsky Roller-Contact Unit in a Moulded Casing
Podolsky's variable resistor (Wirt Company, US 2,060,114, 1936). The carbon strip is bent into a ring inside a moulded casing, and instead of a sliding wiper a small roller runs round it. A coil spring presses the roller out against the strip with even pressure in every position, even over slight irregularities. The patent gives no sizes; the parts are named by what they do.
The picture: the patent's drawing (Figs. 8 and 9).
Miðlungs
2 hours
Leiðbeiningar
1
1
Seat the strip in the casing
Seat the strip in the casing
Bend the resistance strip into a ring against the round inner wall of the moulded casing. A small rib across the wall stops both ends of the strip so it cannot shift; the thick part at the rib has a hole for bolting the casing to a panel. Ours: flat-nose pliers to ease the strip in.
Efni fyrir þetta skref:
Moulded Insulating Casing1 stykki
Kolefnisviðnámsþáttur1 stykkiNauðsynleg verkfæri:
Flatkjaftatöng2
2
Bolt the terminals
Bolt the terminals
Put two terminal bolts through the casing wall, one at each end of the strip. Under each bolt head a small contact plate rests on the coated end of the strip.
Efni fyrir þetta skref:
Tengibolti2 stykki
Contact Plate2 stykkiNauðsynleg verkfæri:
Nefjatöng3
3
Fit shaft, sleeve, collar and yoke
Fit shaft, sleeve, collar and yoke
The shaft turns in a sleeve fixed in the base of the casing. A collar on the shaft rests on the outer end of the sleeve; on the inner end the shaft carries a yoke, with a spring washer between yoke and sleeve so the shaft cannot slide. Ours: pliers to seat the spring washer.
Efni fyrir þetta skref:
Stýriöxull1 stykki
Shaft Sleeve1 stykki
Shaft Collar1 stykki
Shaft Yoke1 stykki
Spring Washer1 stykkiNauðsynleg verkfæri:
Nefjatöng4
4
Fit the sprung roller
Fit the sprung roller
The yoke's slotted ends guide a flat stem. The roller sits in the stem's forked outer end. A washer on shoulders of the stem, pushed out by a coil spring, holds the roller on the strip with even pressure all the way round.
Efni fyrir þetta skref:
Roller Stem1 stykki
Contact Roller1 stykki
Flöt skinna1 stykki
Coil Spring1 stykkiNauðsynleg verkfæri:
NefjatöngEfni
13- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2 stykkiStaðgengill
- 2 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.