Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)
Frank L. Pritchard · Public domain
Forge

Búin til af

Forge

13. nóvember 2026NO
0
0
0
0
0

Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)

Frank L. Pritchard of Parker, Arizona, received US 2,231,593, dated 11 February 1941, for a tubing cutter small enough for a mechanic's tool box. The tube sits in a V in a fixed jaw. A movable jaw slides on the adjusting screw and a guide pin, with a spring pushing the jaws apart. The cutting wheel is held by a pivoted support with threads on its inner edge. Swung down, the support lets go of the screw, so the jaw can be pushed straight onto any tube. Swung up, it meshes with the screw again and the screw feeds the wheel in. We make his parts from steel bar and plate. All sizes are ours.
Miðlungs
About 3 days

Leiðbeiningar

1

The swing that lets go

Hleð Jupyter-vinnubók…
2

Read US 2,231,593

"The pivoted blade support 16 may swing downwardly until the threads thereof will be free of the threads of the screw 8. The movable jaw 6 may now be slid downwardly until the pivoted blade support is in its proper cutting position."
3

Print the template

Both jaws, the blade support, the wheel and a 15 mm tube at 1:1, with the screw, pin and pivot holes. print at 100 % (check the 50 mm bar).
HönnunarskráPDFCC0 - Free
Sækja líkan
4

Make the stationary jaw

Saw 64 mm of 16 mm square bar, or of 16 mm plate. File the 90 degree V 8 mm deep in its top face. Drill the 6 mm pin hole and a 10 mm hole for the screw, and counterbore the pin hole 10 mm across, 5 mm deep, for the spring. Drill the 3 mm cross-pin hole across the jaw so it just cuts into the side of the screw hole.

Efni fyrir þetta skref:

Plata úr mjúku stáliPlata úr mjúku stáli1 stykki

Nauðsynleg verkfæri:

JárnsögJárnsög
ÞjalasettÞjalasett
SúluborSúlubor
VélskrúfstykkiVélskrúfstykki
BorasettBorasett
KörnunardorgKörnunardorg
RissnálRissnál
SkrúfstykkiSkrúfstykki
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
5

Make the movable jaw and the support

Saw the movable jaw 50 mm long from the same bar. Drill the 6.2 mm pin hole and its spring counterbore. Saw and file a slot 8.2 mm wide down its middle, from 22 mm to the end. Saw the blade support from 14 mm plate to the template. File its upper part down to 8 mm thick, centred, so it slides into the slot, and file away its lower inner corner. Saw a 7 mm slot up its lower part for the wheel. Drill the pivot and stop-pin holes through the jaw and support together, and file the stop-pin hole in the support into a short slot.

Efni fyrir þetta skref:

Plata úr mjúku stáliPlata úr mjúku stáli1 stykki

Nauðsynleg verkfæri:

JárnsögJárnsög
ÞjalasettÞjalasett
NálaþjalasettNálaþjalasett
SúluborSúlubor
VélskrúfstykkiVélskrúfstykki
BorasettBorasett
SkrúfstykkiSkrúfstykki
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
6

Tap the half nut

Pin the support in the jaw, swung up, and clamp it there. Drill 6.8 mm down the screw axis through both, so the drill cuts a shallow groove in the support's inner edge, then tap it M8 through both. Take the support out and open the jaw's own hole to 8.5 mm, so the screw passes freely and only the support's threads hold it.

Nauðsynleg verkfæri:

SúluborSúlubor
VélskrúfstykkiVélskrúfstykki
BorasettBorasett
SnittsettSnittsett
SkurðarolíaSkurðarolía
7

Make the screw and the guide pin

Turn the top 62 mm of a 90 mm piece of 10 mm bar to 8 mm and cut an M8 thread on it with the die. Turn a groove 1.5 mm deep and 3.2 mm wide in the plain part, where the cross pin will sit, and drill a 6 mm hole across its bottom end for a T-bar. Cut the guide pin, 80 mm of 6 mm rod, and drill a 3 mm hole across its top for the stop pin.

Efni fyrir þetta skref:

Sívöl stöng úr mjúku stáliSívöl stöng úr mjúku stáli1 stykki
Kringlótt stöng úr deigu stáliKringlótt stöng úr deigu stáli1 stykki

Nauðsynleg verkfæri:

MálmrennibekkurMálmrennibekkur
Þríkjálka rennibekkspatrónaÞríkjálka rennibekkspatróna
RennibekkjarstálRennibekkjarstál
FráskurðarjárnFráskurðarjárn
SnittsettSnittsett
SúluborSúlubor
BorasettBorasett
JárnsögJárnsög
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Efni fyrir þetta skref:

VerkfærastálsstöngVerkfærastálsstöng1 stykki

Nauðsynleg verkfæri:

MálmrennibekkurMálmrennibekkur
Þríkjálka rennibekkspatrónaÞríkjálka rennibekkspatróna
RennibekkjarstálRennibekkjarstál
FráskurðarjárnFráskurðarjárn
Sett af miðjuborumSett af miðjuborum
BorasettBorasett
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
ÖryggisglerauguÖryggisgleraugu
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Nauðsynleg verkfæri:

AflinnAflinn
SmiðjutöngSmiðjutöng
Lítill segullLítill segull
HerslufataHerslufata
VatnVatn
BrýniBrýni
SuðuhanskarSuðuhanskar
ÖryggisglerauguÖryggisgleraugu
10

Assemble

Drive the guide pin into the stationary jaw. Put the screw into its hole from below and drive the cross pin in so it lies in the groove; the screw must still turn. Fit the T-bar. Slip the spring over the guide pin, then the movable jaw over the pin and the screw, and put the stop pin across the top. Fit the wheel in the support on its 5 mm pin, and pin the support into the jaw with its pivot and stop pins. Rivet a 1.5 mm steel strip along the top of the jaw, sticking out past the support as a thumb piece. Oil the threads.

Efni fyrir þetta skref:

StálpinniStálpinni5 stykki
ÞrýstigormasettÞrýstigormasett1 stykki
FjaðurstálræmaFjaðurstálræma1 stykki
StálhnoðStálhnoð2 stykki
Kringlótt stöng úr deigu stáliKringlótt stöng úr deigu stáli1 stykki

Nauðsynleg verkfæri:

KúluhamarKúluhamar
KörnunardorgKörnunardorg
SkrúfstykkiSkrúfstykki
SúluborSúlubor
BorasettBorasett
SkurðarolíaSkurðarolía
11

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Swing the support down, push the movable jaw down until the wheel touches the tube in the V, swing it up into the screw, and tighten the screw a little. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Efni fyrir þetta skref:

KoparrörKoparrör1 stykki

Nauðsynleg verkfæri:

SkrúfstykkiSkrúfstykki
GratáhaldGratáhald
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
12

Troubleshooting

Swing-nut tubing cutter troubleshooting.

Flow

Loading...
13

History and honest limits

**Frank L. Pritchard** of Parker, Arizona, US 2,231,593, dated 11 February 1941, filed 17 November 1939. He claimed "a pivoted blade support mounted on the movable jaw and having threads on the inner edge thereof adapted to engage the threads of said screw". His movable jaw had a bushing for the guide pin and a looped handle on the screw head; ours has a drilled hole and a T-bar. The patent gives no sizes or materials; all of ours are ours.

Efni

9

Nauðsynleg verkfæri

27

Hönnunarskrár

1

Þessi teikning býr til

Thumbnail
Tímabundinn texti

Rörskeri

Free

310
0
1

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)

V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)

eftir ForgeNO

Málmsmíði

0
0
0
0
0
0
Taps and Dies Cut on the Lathe, with Wrench and Stock

Taps and Dies Cut on the Lathe, with Wrench and Stock

eftir MartinNO

Málmsmíði

25
0
0
0
6
0
Reamer: a Fluted Hand Reamer Turned, Fluted, Hardened and Stoned (Markham, 1908)

Reamer: a Fluted Hand Reamer Turned, Fluted, Hardened and Stoned (Markham, 1908)

eftir ForgeNO

Málmsmíði

7
0
0
0
0
0

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...