Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)
A separating funnel holds two liquids that do not mix, so the lower layer can be run off through a tap at the bottom. J. P. Demers (US 5,580,528, 1996) fuses a bought glass stopcock to the bottom of a pear-shaped glass vessel and screws a flexible plastic stem onto it, because the usual glass stem breaks just below the stopcock.
The glass stopcock body stays clear, so you can watch the boundary between the two liquids as it reaches the tap.
Source: J. P. Demers, US Patent 5,580,528 (filed 1995, granted 1996). Picture: its Figs. 1-3.
Lengra kominn
Unknown
Leiðbeiningar
1
1
Read Demers
Read Demers
"The stresses resulting from such impacts usually fracture the glass just below the stopcock, or else chip off the end of the stem ... When the fracture is close to the stopcock, repair is impossible without replacing the stopcock".
2
2
Blow the vessel
Blow the vessel
Blow a glass vessel, pear-shaped (or spherical or cylindrical), with a neck at the top for pouring in the liquids and an opening at the bottom. Glass, size and how it is blown are not given; the patent leaves this to a scientific glassblower.
Efni fyrir þetta skref:
Óþekkt gler1 vesselNauðsynleg verkfæri:
Glerblástursbrennari fyrir borð
Óþekkt mótunaraðferð
Óþekkt mál3
3
Fuse on the stopcock
Fuse on the stopcock
Take a glass-bodied stopcock (bought: the patent calls them articles of commerce, with a glass or PTFE plug) and fuse its upper stem to the bottom of the vessel so the vessel opens straight into the stem. Form a male thread on the end of its lower stem (how is not given).
Efni fyrir þetta skref:
Glerkrani1 plug of glass or PTFENauðsynleg verkfæri:
Glerblástursbrennari fyrir borðÓþekkt mótunaraðferð4
4
Make the plastic stem
Make the plastic stem
Make a stem of moderately flexible plastic tube with a female thread in its upper end and an inner shoulder where the end of the glass thread meets it. Lay an O-ring on the shoulder when the funnel will hold reactive or toxic liquids or work under pressure or vacuum. Cut the lower end at about 45 degrees as a drip tip. The plastic is not given.
Efni fyrir þetta skref:
Óþekktur efniviður1 flexible plastic stem
O-hringur1 stykkiNauðsynleg verkfæri:
Óþekkt mótunaraðferðÓþekkt mál5
5
Assemble and use
Assemble and use
Screw the plastic stem onto the glass thread. Close the stopcock, pour the two liquids in at the neck, shake and let them separate, then turn the plug to line its bore up with the stems and run the lower layer off, watching the boundary through the glass stopcock. Unscrew the stem to clear a blocked stopcock.
Efni
4- 1 vesselStaðgengill
- 1 plug of glass or PTFEStaðgengill
- 1 flexible plastic stemStaðgengill
- 1 stykkiStaðgengill
Þessi teikning býr til
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.