Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Shaded Forge Goggles: Ventilated Eye Cups with a Coloured and a Clear Lens (Tully, US 1,679,105)
George L. Tully and Solomon Lacasse · Public domain (US patent drawing)
Forge

Búin til af

Forge

4. nóvember 2026NO
10
0
0
0
0

Shaded Forge Goggles: Ventilated Eye Cups with a Coloured and a Clear Lens (Tully, US 1,679,105)

Molten metal and glass give off a strong glare, and goggles worn over hot work steam up. George L. Tully and Solomon Lacasse of the American Optical Company (filed 1927, US 1,679,105) made goggles for welders and "those employed in handling molten metal, glass and similar products": hard-rubber or Bakelite eye cups with a coloured inner lens against the glare and a cheap clear outer lens that is easily replaced, held apart by a crimped spring under a bayonet cap. Slots let air through between the lenses and inside the cup, so the lenses do not steam up. This rung turns the eye cups from ebonite, cuts the lenses and assembles the goggles. Not given: any size, the metal of the cap, spring and chain, the band's material and the shade of the coloured glass. Source: G. L. Tully and S. Lacasse, US 1,679,105 (1928). Picture: the patent's Figs. 1-4.
Miðlungs
About 6 hours

Leiðbeiningar

1

Read US 1,679,105

"The inner lens being preferably of colored glass to reduce the glare from the molten material and the outer lens being of plain glass. Colored glass is expensive, whereas the outer plain glass is cheap and economical. If the outer glass is broken it can be easily replaced, or if it becomes scratched or marred so as to become semi-opaque a new lens can be quickly and easily inserted for the old one."
2

Turn the eye cups

Turn two annular eye cups from ebonite (hard rubber, one of his two materials) on the lathe. Inside each, leave a shouldered flange near the front to carry the inner lens. Cut the eye side of the cup on an angle and shape it to fit the face. Saw two slots opposite each other through the wall in front of the flange, between the lenses, and two more behind the flange for air between the inner lens and the eye. The sizes are ours.

Efni fyrir þetta skref:

EbónítstöngEbónítstöng1 as required

Nauðsynleg verkfæri:

MálmrennibekkurMálmrennibekkur
Rennijárnasett (HSS)Rennijárnasett (HSS)
JárnsögJárnsög
NálaþjalasettNálaþjalasett
ÖryggisglerauguÖryggisgleraugu
3

Cut the lenses

For each cup, cut a round inner lens from coloured glass and a round outer lens from plain glass to fit the cup, and grind their edges smooth.

Efni fyrir þetta skref:

Litaðar glerplöturLitaðar glerplötur2 stykki
GlerplataGlerplata2 stykki

Nauðsynleg verkfæri:

GlerskeriGlerskeri
SlípiskífaSlípiskífa
ÖryggisglerauguÖryggisgleraugu
4

Make the caps, springs and shields

For each cup make an annular cap that fits over the cup's front flange, with two bayonet slots in its lower edge and two slots opposite each other that line up with the cup's front slots. Crimp a ring of thin metal into a wave to sit between the lenses. Bend a shield closed on three sides and open at the bottom to cover one of the rear slots, and rivet it to the cup.

Efni fyrir þetta skref:

Óþekktur málmurÓþekktur málmur1 as required

Nauðsynleg verkfæri:

PlötuklippurPlötuklippur
NálaþjalasettNálaþjalasett
SúluborSúlubor
HnoðsettHnoðsett
KúluhamarKúluhamar
5

Fit the lenses

Drop the coloured lens onto the cup's flange, lay the crimped spring on it, then the clear lens, and slide the cap on so its bayonet slots pass over two stud screws in the cup. Turn the cap and tighten the screws. The spring lets the outer lens yield if it is struck. To change a lens, loosen the screws, slide the cap back and push the lenses out from inside.

Efni fyrir þetta skref:

VélskrúfurVélskrúfur4 stykki

Nauðsynleg verkfæri:

SkrúfjárnasettSkrúfjárnasett
SúluborSúlubor
6

Bridge and band

Join the two cups with a short chain covered with rubber tubing. Fix an elastic head band to the outer sides of the cups with an adjustable buckle.

Efni fyrir þetta skref:

Óþekktur málmurÓþekktur málmur1 as required
GúmmíslangaGúmmíslanga1 as required
Óþekktur efniviðurÓþekktur efniviður1 as required
Koparsylgja með tunguKoparsylgja með tungu1 stykki

Nauðsynleg verkfæri:

SkrúfjárnasettSkrúfjárnasett
7

The patent drawing

US 1,679,105, Figs. 1-4: the goggles (1), a cup from the side with the shield (2), a section through cup, lenses and cap (3) and a section through the lenses and spring (4). Public domain (expired patent).
8

History and honest limits

Tully and Lacasse filed on 16 May 1927 for the American Optical Company of Southbridge, Massachusetts; the patent was granted on 31 July 1928. The patent gives no sizes and no shade for the coloured glass, so our goggles are not rated to any welding or furnace filter standard; do not rely on them for electric-arc welding. The cap, spring, chain and shield metal and the band's elastic material are not named (unknown).

Efni

8

Nauðsynleg verkfæri

12

Þessi teikning býr til

Thumbnail
Tímabundinn texti

Dökk smiðjugleraugu

Free

290
0
1

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...