LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Reading a Potentiometer — SIK Circuit 2
Ed

Búin til af

Ed

17. mars 2026FI
80
0
0
0
0

Reading a Potentiometer — SIK Circuit 2

Learn to read analog input from a potentiometer and use it to control LED blink speed. Turn the knob to make the LED blink faster or slower — your first step into analog sensors!

Leiðbeiningar

1

Parts & Introduction

In this experiment you'll use a potentiometer (a variable resistor with a knob) to control how fast an LED blinks. This introduces analogRead() — reading voltage levels between 0 and 5V as values from 0 to 1023.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 1x Potentiometer (10K)
  • 1x LED (any color)
  • 1x 330Ω Resistor
  • 6x Jumper Wires

Efni fyrir þetta skref:

SparkFun Inventor's Kit - V3.2SparkFun Inventor's Kit - V3.21 sett

Nauðsynleg verkfæri:

Computer with Arduino IDEComputer with Arduino IDE
2

Hardware Hookup

Wiring Instructions

  1. Place the potentiometer in the breadboard. It has three pins.
  2. Connect the left pin to GND and the right pin to 5V (or vice versa).
  3. Connect the middle pin (wiper) to Analog Pin A0.
  4. Place an LED in the breadboard. Connect the positive leg (longer) to Digital Pin 13.
  5. Connect the negative leg (shorter) through a 330Ω resistor to GND.
  6. Connect the 5V and GND rails on the breadboard to the Arduino.

Efni fyrir þetta skref:

BreadboardBreadboard1 stykki
Jumper WiresJumper Wires6 stykki
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

potentiometer.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 02 — POTENTIOMETER

Measure the position of a potentiometer and use it to
control the blink rate of an LED. Turn the knob to make
it blink faster or slower!

This code is completely free for any use.
Visit http://learn.sparkfun.com/products/2 for SIK information.
*/

int sensorPin = 0;    // Potentiometer on analog pin 0
int ledPin = 13;      // LED on digital pin 13

void setup()
{
  pinMode(ledPin, OUTPUT);
}

void loop()
{
  int sensorValue;

  sensorValue = analogRead(sensorPin);

  digitalWrite(ledPin, HIGH);
  delay(sensorValue);

  digitalWrite(ledPin, LOW);
  delay(sensorValue);
}

Efni fyrir þetta skref:

Arduino Uno R3Arduino Uno R31 stykki

Nauðsynleg verkfæri:

Computer with Arduino IDEComputer with Arduino IDE
4

Test & Experiment

What You Should See

The LED blinks faster or slower as you turn the potentiometer knob. At one extreme it blinks very fast, at the other it blinks slowly.

Troubleshooting

  • Sporadically working: The potentiometer pins may not be making good contact. Press it firmly into the breadboard.
  • Not working: Make sure the wiper (middle pin) goes to Analog pin 0, not Digital pin 0.
  • LED not lighting: LEDs only work in one direction. Flip it around.

Experiments to Try

  • Open the Serial Monitor and print the sensorValue to see the raw numbers (0-1023).
  • Use map() to convert the sensor range to a brightness range and control LED brightness with analogWrite().

Efni

7

Nauðsynleg verkfæri

1
Áætlað alls
Það sem smiðurinn keypti. Efni án verðs færðu þar sem þú kaupir það.
$108.84

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...