LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
GRÆN FRAMTÍÐ
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Using a Flex Sensor — SIK Circuit 9
Ed

Búin til af

Ed

17. mars 2026FI
30
0
0
0
0

Using a Flex Sensor — SIK Circuit 9

Use a flex sensor to control a servo motor. Bend the sensor to move the servo — combining analog input with motor control for gesture-based interaction.

Leiðbeiningar

1

Parts & Introduction

A flex sensor changes resistance when bent. Combined with the servo from Circuit 8, you can create gesture-based controls — bend the sensor to move the servo. This combines analogRead() with the Servo library.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 1x Flex Sensor
  • 1x Servo Motor
  • 1x 10KΩ Resistor
  • 11x Jumper Wires

Efni fyrir þetta skref:

SparkFun Inventors Kit - V3.2SparkFun Inventors Kit - V3.21 kit
Arduino Uno R3Arduino Uno R31 piece
BreadboardBreadboard1 piece
Flex SensorFlex Sensor1 piece
Servo MotorServo Motor1 piece
10K Ohm Resistor10K Ohm Resistor1 piece
Jumper WiresJumper Wires7 pieces

Nauðsynleg verkfæri:

Computer with Arduino IDE
2

Hardware Hookup

Wiring Instructions

Flex Sensor
  1. Connect one pin of the flex sensor to 5V.
  2. Connect the other pin to Analog Pin A0.
  3. Connect a 10K resistor from Analog Pin A0 to GND (voltage divider).
Servo
  1. Connect Red wire to 5V.
  2. Connect Black wire to GND.
  3. Connect White wire to Digital Pin 9.

Efni fyrir þetta skref:

Flex SensorFlex Sensor1 piece
Servo MotorServo Motor1 piece
10K Ohm Resistor10K Ohm Resistor1 piece
BreadboardBreadboard1 piece
Jumper WiresJumper Wires7 pieces
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

flex_sensor.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 09 — FLEX SENSOR

Use the flex sensor to change the position of a servo.

Hardware connections:
  Flex sensor: one pin to analog pin 0 (with 10K to GND), other pin to 5V
  Servo: RED to 5V, WHITE to pin 9, BLACK to GND

This code is completely free for any use.
*/

#include <Servo.h>

Servo servo1;

const int flexpin = 0;

void setup()
{
  Serial.begin(9600);
  servo1.attach(9);
}

void loop()
{
  int flexposition;
  int servoposition;

  flexposition = analogRead(flexpin);

  servoposition = map(flexposition, 600, 900, 0, 180);
  servoposition = constrain(servoposition, 0, 180);

  servo1.write(servoposition);

  Serial.print("sensor: ");
  Serial.print(flexposition);
  Serial.print("  servo: ");
  Serial.println(servoposition);

  delay(20);
}

Efni fyrir þetta skref:

Arduino Uno R3Arduino Uno R31 piece

Nauðsynleg verkfæri:

Computer with Arduino IDE
4

Test & Experiment

What You Should See

The servo moves in response to bending the flex sensor. Open the Serial Monitor to see both the raw sensor value and the mapped servo position.

Troubleshooting

  • Servo not moving: Check servo wiring — easy to plug in backwards.
  • Sensor only works one way: The flex sensor bends in one direction. The striped side should face outward on a convex curve.
  • Limited range: Adjust the map() range values (600, 900) to match your sensor's actual readings from the Serial Monitor.

Experiments to Try

  • Build a "robot finger" that mimics your finger bending.
  • Replace the servo with an LED and control brightness by bending.

Efni

7

Nauðsynleg verkfæri

1
  • 13
    Computer with Arduino IDE
Estimated Total
$163.00

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...