LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Solenoid: Iron-Clad Valve Magnet with Two Coils, 1860 and 1765 Turns (Nachod 1905, in Underhill 1910)
A short-stroke solenoid that opens an air valve. One coil pulls the iron armature down; a second, weaker coil holds it there against the air pressure once the first is switched off. A cast-iron shell closes the magnetic circuit around both.
Result: an iron-clad plunger solenoid driving a brass valve rod through its hollow core.
Source: C. P. Nachod's test (Electrical World, 1905) in Underhill, Solenoids, Electromagnets and Electromagnetic Windings (1910), pp. 125-129. Unknown: the wire insulation; the test does not give it. Not given: shell and armature sizes, voltage. Picture drawn by Youblob.
Lengra kominn
2 days
Leiðbeiningar
1
1
Turn the core and armature
Turn the core and armature
Turn the core from Norway iron to 3.17 cm outside diameter and bore a 0.95 cm hole through it for the valve rod. Turn the armature from the same iron. Ours: wrought iron bar; the armature size is not given.
Efni fyrir þetta skref:
Smíðajárnsstöng1 as requiredNauðsynleg verkfæri:
Rennijárnasett (HSS)2
2
Cast the shell and top
Cast the shell and top
Cast the shell and top in cast iron so they close the magnetic circuit round the coils, leaving a round clearance gap for the armature in the top. Sizes: not given (Underhill's Fig. 92 shows the layout).
Efni fyrir þetta skref:
Hrájárnsstykki1 as requiredNauðsynleg verkfæri:
Kúpólbræðsluofn
Mótakassi
Mótasandur3
3
Wind coil A: 1860 turns of No. 25
Wind coil A: 1860 turns of No. 25
Wind the operating coil, 1860 turns of No. 25 wire, and place it where it encircles the working air gap between armature and core. Copper, as Underhill gives for magnet windings. Unknown: the insulation; the test does not give it.
Efni fyrir þetta skref:
Koparvír1 as required
Óþekkt einangrunarefni1 as requiredNauðsynleg verkfæri:
Rennijárnasett (HSS)4
4
Wind coil B: 1765 turns of No. 26
Wind coil B: 1765 turns of No. 26
Wind the retaining coil, 1765 turns of No. 26 wire, and place it below coil A on the core. Being away from the gap, it pulls only 0.4-0.8 as hard as A, enough to hold the armature down.
Efni fyrir þetta skref:
Koparvír1 as requiredNauðsynleg verkfæri:
Rennijárnasett (HSS)5
5
Assemble with the brass valve rod
Assemble with the brass valve rod
Fit core, coils and armature in the shell and pass the brass rod through the core to the valve. Nachod set test gaps of 0.41 and 2.05 mm with brass washers.
Efni fyrir þetta skref:
Messingstöng1 as requiredNauðsynleg verkfæri:
Rennijárnasett (HSS)Efni
5- 1 as requiredStaðgengill
- 1 as requiredStaðgengill
- 2 as requiredStaðgengill
- 1 as requiredStaðgengill
- 1 as requiredStaðgengill
Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.