LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Spring-Wire Twin Dash Churn: Two Hinged Dashes Rocked by a Sprung Wire on a Crank
Dugdale made the link between crank and dashes a spring.
Samuel G. Dugdale of Richmond, Indiana, received US 8,219, dated 15 July 1851, for a churn: a water-tight box 16 inches long, nine wide and twelve deep, with two perforated dashes seven by six inches hung by hooks on staples three inches above the bottom at each end. A shaft with a three-inch crank turns in grooves in the box's edges, held down by the lid; an elastic wire bent round the crank, closed into an eye, has its ends hooked into staples on the dashes, "in such a manner that it will accommodate itself to the opening and closing of the same."
This rung works out the dashes' swing, then prints the two dashes and shaft bearings, bends the spring wire, and makes butter.
Byrjandi
About 2 hours, plus printing
Leiðbeiningar
1
1
The dashes' swing
The dashes' swing
Hleð Jupyter-vinnubók…
2
2
Two dashers worked from one motion before it
Two dashers worked from one motion before it
The embedded blueprint links two dashers with levers. Dugdale links his two hinged dashes to one crank with a single sprung wire.
3
3
Read US 8,219
Read US 8,219
"It will be noticed, also, that when the handle is raised perpendicular, the crank to which the wire is attached will be parallel to it, and the ends of the wire attached to the dashers, will be extended, and as the handle is turned from you the springs act upon the dashers tending to force them down, thereby facilitating the operation."
4
4
Print the parts
Print the parts
Print two perforated dashes with their hooks and staple and two shaft bearings. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Efni fyrir þetta skref:
PETG-þráður1 stykkiNauðsynleg verkfæri:
FDM-þrívíddarprentari5
5
Print the dash
6
6
Print the shaft bearing
Print the shaft bearing
The shaft bearing, printed as step 4 describes.
7
7
Box and staples
Box and staples
Take a food-safe box about 240 × 135 × 180 mm, about three fifths of his. Screw a stainless screw-eye into each end 30 mm above the bottom as the staples, and hang a dash on each by its hooks, holes toward the middle. Screw the bearings to the box's long edges at the middle.
Efni fyrir þetta skref:
Geymslubox í matvælaflokki1 stykki
Tréskrúfa #8 x 1"1 stykkiNauðsynleg verkfæri:
Hleðslubor
Borasett
Skrúfjárnasett8
8
Crank and spring wire
Crank and spring wire
Bend a 6 mm steel rod into a shaft with a 45 mm crank in the middle and a handle at one end, and lay it in the bearings. Bend spring-steel wire once round the crank pin into an eye and hook its two ends into the dashes' staples, so the wire is a little stretched with the crank up.
Efni fyrir þetta skref:
Kringlótt stöng úr deigu stáli1 stykki
Fjaðurstálsvír1 stykkiNauðsynleg verkfæri:
Skiptilykill
Járnsög9
9
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the box with one side off to show the two perforated dashes hooked to the ends, the spring wire from the crank to their inner ends, and the shaft.
10
10
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres, enough to cover the dashes. Fit the lid over the shaft and turn the handle steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Efni fyrir þetta skref:
Rjómi2000 ml
Gróft sjávarsalt1 stykki
Vatn1 stykkiNauðsynleg verkfæri:
Hitamælir með nema sem situr í
Skeiðklukka
Stafræn eldhúsvog
Stór hrærskál úr ryðfríu stáli11
11
Dashes that jump off, a wire that kinks
Dashes that jump off, a wire that kinks
Spring-wire twin dash troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Samuel G. Dugdale** of Richmond, Wayne County, Indiana, received US 8,219, dated 15 July 1851. His dashes were half an inch thick with holes leaving 2½ inches plain at the hung ends; collars kept the shaft from slipping; it could be turned by a handle or a pinion on a driving wheel. He claimed "the application of the spring wire ... which connects the crank with the dashers."
**Honest limits.** A food-safe box at about three-fifths scale and printed dashes stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Efni
8- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 2000 mlStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
10- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
3Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
Double-Dasher Lever Churn: Swing One Lever, One Dasher Rises as the Other Falls
eftir Woody
Trésmiði
36
0
0
0
0
0
Twin-Plunger Air-Chamber Churn: Two Plungers Throw the Cream Through a Middle Chamber
eftir Emma
MATUR OG DRYKKUR
32
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
eftir TheChef
HANDVERK
54
0
0
0
0
0
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.