LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
GRÆN FRAMTÍÐ
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Building a Nyckelharpa — The Swedish Keyed Fiddle
Woody

Búin til af

Woody

3. júlí 2026NO
0
0
0
0
0

Building a Nyckelharpa — The Swedish Keyed Fiddle

Build a nyckelharpa: a bowed Swedish fiddle played not with fingers on a fingerboard but with a row of wooden KEYS whose tangents press the string to each note. It also carries sympathetic strings that ring on their own. A serious maker build in the bowed string, the tangent keyboard and sympathetic resonance.
Miðlungs
Several hours over several sessions

Leiðbeiningar

1

A fiddle with a keyboard

The nyckelharpa is a bowed Swedish fiddle, but instead of pressing the strings with your fingers you press wooden KEYS. Each key drives a little tangent against the string to make a note.
2

Build the soundbox

Build a long, hollow wooden body with a light soundboard on top. This box amplifies the bowed strings.

Efni fyrir þetta skref:

Baltic Birch Plywood (1/8 inch, 12x12, 10-Pack)Baltic Birch Plywood (1/8 inch, 12x12, 10-Pack)1 piece
Dry Softwood BoardDry Softwood Board1 piece
PVA Wood GluePVA Wood Glue1 piece

Nauðsynleg verkfæri:

HacksawHacksaw
3

Fit the strings

Stretch a melody string and one or two drone strings along the top, over a bridge, tuned with pegs.

Efni fyrir þetta skref:

Steel Music Wire 0.032"Steel Music Wire 0.032"1 piece
Tuning PegsTuning Pegs4 piece

Nauðsynleg verkfæri:

AwlAwl
4

Add sympathetic strings

Under the melody string, run a set of thin strings you never touch — the SYMPATHETIC strings. Tuned to the scale, they ring on their own whenever their note is played, giving the halo of sound.

Efni fyrir þetta skref:

Steel Music Wire 0.032"Steel Music Wire 0.032"1 piece
5

Build the key-box

Build a box under the neck holding a row of sliding wooden keys, each carrying a small hardwood tangent.

Efni fyrir þetta skref:

Dowel RodDowel Rod1 piece

Nauðsynleg verkfæri:

Sloyd Carving KnifeSloyd Carving Knife
6

Set the tangents

Position each key's tangent so that pressing the key from below stops the melody string at the next note of the scale — a keyboard of frets you push up into the string.
7

Make the bow

String a short springy stick with horsehair to make a bow, and rub it with pine rosin.

Efni fyrir þetta skref:

Curved Branch (Bow)Curved Branch (Bow)1 piece
Bow Hair (Horsehair)Bow Hair (Horsehair)1 piece
8

Bow and key

Hold the harpa across your body on a strap, bow the strings with one hand, and press the keys with the other. The keys pick out the tune while the drones and sympathetic strings shimmer beneath.
9

Compendium — bowing through a keyboard

The nyckelharpa joins two ideas. First it is a bowed instrument: drawing a rosined bow across a string sets it into steady stick-slip vibration, the same Helmholtz motion as the erhu or violin, so the note sings on as long as you bow. Second, it is stopped by a KEYBOARD rather than by fingers: each key carries a tangent, a little hard ridge that pushes against the string to shorten its speaking length to a fixed note, exactly as a fret does — the same mechanism that fingers the melody on a hurdy-gurdy, but here you bow by hand instead of turning a wheel. What gives the nyckelharpa its glittering, cathedral-like tone is a third set of strings, the SYMPATHETIC strings, stretched under the melody string and never touched: each is tuned to a note of the scale, and whenever that note sounds on the bowed string, the matching sympathetic string is shaken into vibration by resonance and rings along on its own, wrapping every note in a soft halo — the same resonance trick used by the Indian sitar and sarangi. Played in Sweden since the Middle Ages and pictured on medieval church walls, the nyckelharpa is a cousin of the hurdy-gurdy (its keyed neighbour) and of the whole bowed-string family.

Efni

8

Nauðsynleg verkfæri

3

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...