LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
Martin

Búin til af

Martin

30. september 2026NO
10
0
0
0
0

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It

A plunger pressed straight down by the hand needs a strong push to empty a lemon. A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger." This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
Miðlungs
About 5 hours

Leiðbeiningar

1

The cam's force

Hleð Jupyter-vinnubók…
2

A lever press before it

The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3

Read US 165,638

"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E." "When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4

Build the squeezer and press lemons

**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole. **Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl. **Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin. **Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised. **Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.

Efni fyrir þetta skref:

HarðviðarborðHarðviðarborð2 stykki
HarðviðarkubburHarðviðarkubbur2 stykki
TrétappiTrétappi0.6 metri
TréskrúfurTréskrúfur16 stykki
TrélímTrélím1 stykki
BlikkdósBlikkdós1 stykki
HurðarlömHurðarlöm1 stykki
Kringlótt stöng úr deigu stáliKringlótt stöng úr deigu stáli0.2 metri
NaglarNaglar2 stykki
ToggormurToggormur2 stykki
SítrónaSítróna3 stykki

Nauðsynleg verkfæri:

HandsögHandsög
Stangajárnasett fyrir tréStangajárnasett fyrir tré
RaspRasp
HleðsluborHleðslubor
BorasettBorasett
PlötuklippurPlötuklippur
HamarHamar
SkrúfjárnasettSkrúfjárnasett
JárnsögJárnsög
EldhúshnífurEldhúshnífur
Stafræn eldhúsvogStafræn eldhúsvog
Vinnuhanskar úr leðriVinnuhanskar úr leðri
5

A cam that slips, jams or does not lift

Cam-lever lemon squeezer troubleshooting.

Flow

Loading...
6

History and honest limits

**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever. **Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.

Efni

11

Nauðsynleg verkfæri

12

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...