LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop
Daniel S. Koons and William F. Moughler, Chicago, Illinois · Public domain (expired patent)
YourGrandma

Búin til af

YourGrandma

6. október 2026IS
30
0
0
0
0

The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop

A bath brush fed from a hose runs all the time, or needs a tap out of reach. Daniel S. Koons and William F. Moughler of Chicago received US 634,527, dated 10 October 1899, for "a fountain bath-brush": a false back with a water passage, joined to the brush by a hollow screw whose perforated head lets the water out among the bristles, with a valve that a spring and the water pressure hold shut until a finger presses its stem, and a strap that holds the hand to the brush. This rung works out the finger force, then builds the false back on a scrub brush with a tyre valve as the finger valve, and measures the force and the flow.
Miðlungs
About 3 hours

Leiðbeiningar

1

Force to open the valve

Hleð Jupyter-vinnubók…
2

A brush that feeds itself before it

The embedded blueprint feeds soap from inside a shaving brush. Koons and Moughler feed water, and give the finger a valve to start and stop it.
3

Read US 634,527

"Said valve is held normally closed by means of a spring 9 and also by the water-pressure, as will be obvious." "A strap k is secured at the sides of said back B' and passes over the latter, so that by inserting the hand between said back B' and said strap k the brush can be firmly held and the fingers at the same time kept in position to operate the valve."
4

Bore the false back

Cut a hardwood block 120 × 50 × 22 mm. Drill a 6 mm passage 90 mm along its centre from one end, and a 6 mm hole down from the top to meet it 30 mm from the far end.

Efni fyrir þetta skref:

HarðviðarkubburHarðviðarkubbur1 stykki

Nauðsynleg verkfæri:

SkrúfstykkiSkrúfstykki
HleðsluborHleðslubor
Sett af miðjuspora-borumSett af miðjuspora-borum
ReglustikaReglustika
Tær öryggisglerauguTær öryggisgleraugu
5

Fit the finger valve

Drill a hole across the passage 20 mm from the inlet to take a tyre valve, pin upward. Epoxy it in so the water must pass through it.

Efni fyrir þetta skref:

DekkjaventillDekkjaventill1 stykki
Tveggja þátta epoxýTveggja þátta epoxý1 stykki

Nauðsynleg verkfæri:

HleðsluborHleðslubor
BorasettBorasett
6

Join it to the brush

Drill a 6 mm hole through the scrub brush's back to line up with the outlet. Cut a rubber gasket, and screw the block on with four wood screws.

Efni fyrir þetta skref:

SkrúbburSkrúbbur1 stykki
GúmmíplataGúmmíplata1 stykki
Tréskrúfa #8 x 1"Tréskrúfa #8 x 1"1 stykki

Nauðsynleg verkfæri:

HleðsluborHleðslubor
BorasettBorasett
FöndurhnífurFöndurhnífur
SkrúfjárnasettSkrúfjárnasett
7

Strap and hose

Screw a strip of rubber sheet across the block as a hand strap, over the valve's side. Fit a hose connector to the inlet with brass fittings and PTFE tape.

Efni fyrir þetta skref:

GúmmíplataGúmmíplata1 stykki
Tréskrúfa #8 x 1"Tréskrúfa #8 x 1"1 stykki
MessingtengiMessingtengi1 stykki
PTFE-þéttiborði fyrir snitturPTFE-þéttiborði fyrir snittur1 stykki

Nauðsynleg verkfæri:

SkrúfjárnasettSkrúfjárnasett
SkiptilykillSkiptilykill
8

The patent drawing

US 634,527 drawing sheet, public domain (expired patent).
Skref 8 - Image 1
9

Measure force and flow

Connect the garden hose and turn on the tap. Press the valve pin with the force meter's hook until water runs; note the force. Hold it open over the jug for 30 s and read the flow.
Skref 9 - Image 1

Efni fyrir þetta skref:

VatnVatn1 stykki

Nauðsynleg verkfæri:

Kraftmælir (gormvog)Kraftmælir (gormvog)
MælikannaMælikanna
SkeiðklukkaSkeiðklukka
GarðslangaGarðslanga
10

A valve that drips, sticks or barely flows

Finger-valve bath brush troubleshooting.

Flow

Loading...
11

History and honest limits

**Daniel S. Koons** and **William F. Moughler** of Chicago filed US 634,527 on 21 September 1898; it is dated 10 October 1899. They called it a self-cleansing brush. Its handle is telescopic, with a stuffing-box between the two members, and the hose can be led through it to the brush; a second form uses a nozzle as the screw joining the backs. They did not limit it to the bath. **Honest limits.** A tyre valve stands in for their seated valve and stem, and wood screws for their hollow screw. Your forces and flows are the result.

Efni

9

Nauðsynleg verkfæri

13

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

The Self-Soaping Shaving Brush: A Soap Stick Inside the Bristles

The Self-Soaping Shaving Brush: A Soap Stick Inside the Bristles

eftir YourGrandmaIS

Fegurð og snyrtivörur

24
0
0
0
0
0
The Twin Scrubbing Brush: Two Heads on a Sprung Holder

The Twin Scrubbing Brush: Two Heads on a Sprung Holder

eftir YourGrandmaIS

Vélfræði

33
0
0
0
0
0
The Hose and Its Clip: Why It Was Tight When You Fitted It

The Hose and Its Clip: Why It Was Tight When You Fitted It

eftir MartinNO

Verkfæri

38
0
0
0
0
0

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...