LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
The Free-Spindle Ticket Punch: A Loose Spindle Lifted by a Spring, Close to the Pivot
Warren Hill, Springfield, Massachusetts · Public domain (expired patent)
Emma

Búin til af

Emma

30. september 2026SE
35
0
0
0
0

The Free-Spindle Ticket Punch: A Loose Spindle Lifted by a Spring, Close to the Pivot

A punch whose spindle hangs on a small pivot breaks there, and cannot be set close to the levers' joint where the squeeze is strongest. Warren Hill of Springfield, Massachusetts, received US 79,470, dated 30 June 1868, antedated 5 May 1868, as "an improvement upon the invention of the said William J. Phelps". His spindle is not attached to either lever: it slides in a cylindrical guide, a plate fixed to it projects into a recess over a spiral spring that raises it, and lever A bears on its rounded top. "By this construction I am enabled to place the die-spindle nearer the fulcrum of the levers, and also cause the lever A to bear wholly upon the extreme end of the die-spindle C, and thus increase the power of the punch to perforate the thicker board or paper tickets." Springs on stems at the levers' ends open them and serve as a finger loop, and the stems act as stops. This rung works out the gain from moving the spindle toward the pivot, with a work check, then makes the punch with a free, spring-lifted spindle and punches card of two thicknesses.
Lengra kominn
About 6 hours

Leiðbeiningar

1

Closer to the pivot

Hleð Jupyter-vinnubók…
2

The punch it improves

The embedded blueprint pivots the spindle to one lever. Hill frees it, lifts it with a spring, and sets it nearer the fulcrum.
3

Read US 79,470

"To raise the die-spindle when the levers are opened again, I attach the projecting plate e rigidly to the side of the spindle, which has a circular portion and a neck, which enters the spindle, and is fastened securely therein; or I may form the die-spindle C and its projection e in one piece, or from one piece of metal. Beneath this circular plate e, I form a recess, f′, in B, and insert a spiral spring, f, the upper end of which bears against the plate, and tends to raise the die-spindle." "I am aware that a device has been used as a ticket-punch, as shown in Letters Patent granted to William J. Phelps, and dated September 17, 1867; but my device differs from that very materially in its construction, inasmuch as said Phelps's device has a spindle which is pivoted to one lever by a small pivot, which is liable to breakage"
4

Make the punch and try thick card

**Levers.** Cut two levers from flat bar, A with a semicircular ear at its end and B with cheeks to take it, and join them with a screw b as the pivot. Saw a ticket slot h across B's jaw close to the pivot. **Guide, die and spindle.** Drill a guide j through B above the slot, set a hardened die plate below it with a slightly conical opening g underneath, and file a 5 mm rod as the spindle with a rounded top i. Solder a small washer to its side as the plate e. **Spring.** Drill a recess f′ in B beside the guide, put a short spring in it under the washer, and file a recess c′ in A that bears on the spindle's top. **Opening spring and stops.** Turn a stem m down from each lever's end and fit one long spring over both stems, so it opens the levers and makes the finger loop; leave the stems long enough to stop the levers just as the spindle meets the die. **Test.** Punch thin card and then card twice as thick, reading the squeeze with the spring scale. Compare with the pivoted-spindle punch.

Efni fyrir þetta skref:

Flatstál úr mjúku stáliFlatstál úr mjúku stáli0.35 metri
Kringlótt stöng úr deigu stáliKringlótt stöng úr deigu stáli0.1 metri
Plata úr mjúku stáliPlata úr mjúku stáli1 stykki
Flöt skinnaFlöt skinna1 stykki
Blýlaust pípulagnalóðtinBlýlaust pípulagnalóðtin1 stykki
LóðfeitiLóðfeiti1 stykki
ÞrýstigormasettÞrýstigormasett1 stykki
VélskrúfurVélskrúfur1 stykki
KartonpappírKartonpappír1 stykki

Nauðsynleg verkfæri:

JárnsögJárnsög
Þjalir (handþjöl)Þjalir (handþjöl)
NálaþjalasettNálaþjalasett
SkrúfstykkiSkrúfstykki
HleðsluborHleðslubor
BorasettBorasett
PrópanbrennariPrópanbrennari
LóðboltiLóðbolti
Kraftmælir (gormvog)Kraftmælir (gormvog)
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
Vinnuhanskar úr leðriVinnuhanskar úr leðri
Tær öryggisglerauguTær öryggisgleraugu
5

A punch whose spindle sticks, jumps or stops short

Free-spindle ticket punch troubleshooting.

Flow

Loading...
6

History and honest limits

**Warren Hill** of Springfield, Hampden County, Massachusetts, received US 79,470, dated 30 June 1868, antedated 5 May 1868; J. P. Buckland witnessed it, as he had Phelps's. His levers were pivoted at the end with a semicircular ear on A entering cheeks on B, secured by the screw b; a projection b′ on A met a part g′ on B to limit opening; and a collar on the spindle with the spring round it could replace the side plate. His claim is the spindle C, projection e and spring f with the recessed lever A and slotted lever B. **Honest limits.** Filed flat bar, a soldered washer and bought springs stand in for his made parts. The notebook ignores friction; its forces and lengths are examples. Your punched card is the result.

Efni

9

Nauðsynleg verkfæri

12

Tengd Blueprint

Þessi blueprint deila þekkingu — tækni, efni eða meginreglur

The Die-Spindle Ticket Punch: A Shaped Die on a Pivot, a Slot for the Ticket

The Die-Spindle Ticket Punch: A Shaped Die on a Pivot, a Slot for the Ticket

eftir MartinNO

Málmsmíðaverkfæri

33
0
0
0
0
0
The Coupon-Stringing Ticket Punch: Every Coupon Holed for the Counting Wire

The Coupon-Stringing Ticket Punch: Every Coupon Holed for the Counting Wire

eftir MarkFI

Pappírshandverksverkfæri

25
0
0
0
0
0
Blanking: The Punch, the Die, and the Gap Between Them

Blanking: The Punch, the Die, and the Gap Between Them

eftir ForgeNO

Málmsmíði

39
0
0
0
0
0

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...