LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Woody

Búin til af

Woody

6. október 2026NO
28
0
0
0
0

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles

Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed. Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down. This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Miðlungs
About 4 hours

Leiðbeiningar

1

Sheet speed from the slot

Hleð Jupyter-vinnubók…
2

Water through a brush's back before it

The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3

Read US 840,604

"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4

Cut the slots

On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.

Efni fyrir þetta skref:

SkrúbburSkrúbbur1 stykki

Nauðsynleg verkfæri:

SkrúfstykkiSkrúfstykki
HleðsluborHleðslubor
BorasettBorasett
LaufsögLaufsög
MerkipenniMerkipenni
ReglustikaReglustika
5

Taper the slots

Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.

Nauðsynleg verkfæri:

Stangajárnasett fyrir tréStangajárnasett fyrir tré
HamarHamar
Stafrænn skífmælir 6 tommurStafrænn skífmælir 6 tommur
FöndurhnífurFöndurhnífur
6

Make the manifold

Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.

Efni fyrir þetta skref:

KoparrörKoparrör1 stykki
MessingtengiMessingtengi1 stykki

Nauðsynleg verkfæri:

RörskeriRörskeri
Þjalir (handþjöl)Þjalir (handþjöl)
SkiptilykillSkiptilykill
7

Seat the manifold

Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.

Efni fyrir þetta skref:

SílikonþéttiefniSílikonþéttiefni1 stykki
GúmmíplataGúmmíplata1 stykki
ÁlplataÁlplata1 stykki
Tréskrúfa #8 x 1"Tréskrúfa #8 x 1"1 stykki

Nauðsynleg verkfæri:

PlötuklippurPlötuklippur
SkrúfjárnasettSkrúfjárnasett
FöndurhnífurFöndurhnífur
8

Handle, valve and drip cup

Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.

Efni fyrir þetta skref:

KoparrörKoparrör1 stykki
KúlulokiKúluloki1 stykki
MessingtengiMessingtengi1 stykki
PTFE-þéttiborði fyrir snitturPTFE-þéttiborði fyrir snittur1 stykki
BlikkdósBlikkdós1 stykki
SílikonþéttiefniSílikonþéttiefni1 stykki

Nauðsynleg verkfæri:

RörskeriRörskeri
SkiptilykillSkiptilykill
HleðsluborHleðslubor
BorasettBorasett
9

The patent drawing

US 840,604 drawing sheet, public domain (expired patent).
Skref 9 - Image 1
10

Full flow against throttled

Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.
Skref 10 - Image 1

Efni fyrir þetta skref:

VatnVatn1 stykki

Nauðsynleg verkfæri:

MælikannaMælikanna
SkeiðklukkaSkeiðklukka
ReglustikaReglustika
GarðslangaGarðslanga
11

A sheet that sprays, sputters or leaks

Sheet-of-water fountain brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised. **Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.

Efni

11

Nauðsynleg verkfæri

18

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...