Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Trowel: the Moulder's Trowel Forged from Flat Steel (Modern Shop Practice, 1916)
A trowel with a wide thin steel blade and a short stem cranked up at a right angle to a round handle. Modern Shop Practice (1916) forges it from steel about 1/4 inch by 1 inch: nick it with fullers, draw down the stem, bend it up to a square corner, then thin the blade edge by edge so a small ridge stays where the stem joins (Fig. 121, R).
The foundry uses it to shape and smooth the larger surfaces of a mould; the bottom is ground slightly crowning so the forward edge does not cut into the sand. Blade size, steel grade and the handle are not given.
Source: Modern Shop Practice, vol. 4 (American Technical Society, 1916), Forging p. 65 and Foundry Work pp. 14-15. Picture: Figs. 121-122.
Miðlungs
An hour
Leiðbeiningar
1
1
Read the source
Read the source
"The molder's trowel illustrated in Fig. 121 is a sample of a large class of forgings, having a wide thin face with a comparatively small thin stem forged at one end. The stock used for the trowel would be about 1/4 inch by 1 inch. This is thick enough to allow for the formation of a ridge at R."
2
2
Nick and draw the stem
Nick and draw the stem
Heat the 1/4 × 1 inch steel. Make two nicks across it with fullers near one end (Fig. 122, A) and draw that end down, roughly to size, into the stem.
Efni fyrir þetta skref:
Hrástálsstöng1 barNauðsynleg verkfæri:
Aflinn
Steðji
Járnsmiðshamar
Járnsmiðstöng
Fuller (rásarjárn)
Hitaþolnir hanskar3
3
Bend the square corner
Bend the square corner
Bend the stem up at a right angle and forge it to a square corner (Fig. 122, B), the same way as the square corner of a bracket.
Nauðsynleg verkfæri:
AflinnSteðjiJárnsmiðshamarJárnsmiðstöngHitaþolnir hanskar4
4
Flatten the blade
Flatten the blade
Hold the work with the stem pointing down against the side of the anvil (Fig. 122, C). Strike down so the blows cover the part over the edge of the anvil: all the metal on the anvil is flattened. Swing the piece round to thin the other edge. The small triangle left unworked forms the ridge R. The same result comes from laying the work flat on the anvil face and using a set hammer. Blade width and length are not given (unknown).
Nauðsynleg verkfæri:
AflinnSteðjiJárnsmiðshamarJárnsmiðstöng
Setthamar
Óþekkt málHitaþolnir hanskar5
5
Grind the bottom and fit the handle
Grind the bottom and fit the handle
Grind the bottom of the blade slightly crowning, so it can be rocked a little as it is worked over the sand without the forward edge cutting in. Fit a short round handle that fits the grasp of the hand (Fig. 10); the source does not say what it is made of or how it is fixed to the stem.
Efni fyrir þetta skref:
Verkfæraskaft1 stykkiNauðsynleg verkfæri:
Slípiskífa6
6
History and honest limits
History and honest limits
The book counts sixty or more trowel and slick shapes on the market; the square trowel works into square corners, the finishing trowels cope out along curved pattern edges. Trowels are sold by width and length of blade.
Not given: blade size, steel grade, handle material and fixing, any hardening. Steel Bar Stock stands for the plain "steel" of the source.
Efni
2- 1 barStaðgengill
- 1 stykkiStaðgengill
Þessi teikning býr til
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.