Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Water Bath: Copper Tank with Plug-In Heaters and an Air-Tube Thermostat (Lidberg, US 1,397,766, 1921)
An electric constant-temperature water bath for laboratory and bacteriological work. A copper tank sits in an insulated fibre-board box; two heater tubes and a thermostat tube are soldered through its wall so the heating coils and the switch plug in from outside. A switch adds extra coils to heat the water up quickly; then the thermostat alone holds the set temperature. Perforated trays on adjustable rods hold the tubes or flasks at the depth you choose.
Result: a thermostatic water bath that holds its water at a set temperature.
Source: T. Lidberg (Chicago Surgical & Electrical Co.), US 1,397,766 (1921). Unknown: sizes, the temperature range, the heater wire. Picture: the patent drawing.
Miðlungs
Unknown
Leiðbeiningar
1
1
Build the insulated tank
Build the insulated tank
Make a rectangular box of fibrous board on four short legs and line it with hair felt or cloth. Set a sheet copper tank inside, its walls a little taller than the box and turned over the top edge as a bead. Make perforated trays of several shelves, each with an upright rod hooked at the top for lifting, and on each rod a sliding clip with a set screw whose end rests on the tank edge, to set how deep the tray hangs. Not given: sizes.
Efni fyrir þetta skref:
Óþekktur efniviður1 fibrous board box, legs
Óþekkt efni1 hair felt or cloth lining
Koparplata1 tank
Gataplata í sigti1 trays
Óþekktur málmur1 rods, clips
Vélskrúfur1 stykkiNauðsynleg verkfæri:
Plötuklippur
Lóðbolti
Óþekkt mál2
2
Fit the heater tubes
Fit the heater tubes
Solder two watertight tubes across the tank, each closed at its inner end and open outside the wall, and a third for the thermostat. For each heater, wind two coils on a rod held in the tube by an insulating disk and an end head; join one end of each coil to the rod and the others to plates on the head, and cover the terminals with a cap plate. Slide each heater into its tube. Ours: nichrome wire. Not given: the coil ratings.
Efni fyrir þetta skref:
Koparrör3 heater and thermostat tubes
Tin-blý lóðmálmur1 as needed
Nikrómvír1 four coilsÓþekktur málmur2 rods, plates, caps
Óþekkt einangrunarefni1 disks, headsNauðsynleg verkfæri:
Lóðbolti
Járnsög3
3
Make the air-tube thermostat
Make the air-tube thermostat
In the closed thermostat tube, mount on an insulating disk a strip carrying a thermostatic bar with a contact at its free end. Facing it, pivot an adjustable bar with its own contact on a bracket in the tube's insulating head, held by a spring against an adjusting screw with a knob outside: turning it sets the temperature at which the contacts open. Bridge the contacts with a condenser to stop sparking. The air in the tube takes the bath's temperature and bends the bar. Ours: a bimetallic strip.
Efni fyrir þetta skref:
Tvímálmsræma1 thermostatic barÓþekktur málmur1 strip, bar, bracket, contacts, screwÓþekkt einangrunarefni1 disk, head
Þrýstigormasett1 stykki
Þéttasett1 spark condenserNauðsynleg verkfæri:
Skrúfjárnasett4
4
Wire and use it
Wire and use it
Wire one coil of each heater through the thermostat, and the other coil of each through a hand switch, with a lamp across the supply to show when current flows. To start, close the switch so all four coils heat the water up. Once it is at temperature, open the switch: the thermostat then switches its two coils on and off to hold the bath steady. Lower the trays of tubes or flasks to the depth wanted.
Efni fyrir þetta skref:
Stangarrofi1 stykki
Perustæði1 stykki
Ljósapera1 stykki
Sveigjanleg snúra með kló1 stykkiNauðsynleg verkfæri:
SkrúfjárnasettEfni
17- 1 fibrous board box, legsStaðgengill
- 1 hair felt or cloth liningStaðgengill
- 1 tankStaðgengill
- 1 traysStaðgengill
- 1 strip, bar, bracket, contacts, screwStaðgengill
- 1 stykkiStaðgengill
- 3 heater and thermostat tubesStaðgengill
- 1 as neededStaðgengill
- 1 four coilsStaðgengill
- 1 disk, headStaðgengill
- 1 thermostatic barStaðgengill
- 1 stykkiStaðgengill
- 1 spark condenserStaðgengill
- frá$3.53
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Efni úr tengdum teikningum
Þessi teikning býr til
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.