Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Paul N. Hasluck (ed.) · Public domain (published 1900)
Woody

Búin til af

Woody

4. nóvember 2026NO
7
0
0
0
0

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Miðlungs
Unknown

Leiðbeiningar

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

Efni fyrir þetta skref:

AskborðAskborð1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

Nauðsynleg verkfæri:

HandsögHandsög
HandhefillHandhefill
BugtarhefillBugtarhefill
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

Efni fyrir þetta skref:

HvíteikarborðHvíteikarborð1 stykki
TrétappiTrétappi1 3/16 in pins

Nauðsynleg verkfæri:

BakkasögBakkasög
GrópmeitillGrópmeitill
RissmálRissmál
Handsveifarbor með borHandsveifarbor með bor
Stillanlegur hallamælirStillanlegur hallamælir
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

Efni fyrir þetta skref:

HvíteikarborðHvíteikarborð1 legs 1 1/2 in square, stays
VagnboltiVagnbolti4 3 in

Nauðsynleg verkfæri:

HandsögHandsög
Handsveifarbor með borHandsveifarbor með bor
SkrúfjárnasettSkrúfjárnasett
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

Efni fyrir þetta skref:

FuruborðFuruborð1 1/2 in bottom, 5/8 in sides
OlíumálningOlíumálning1 stykki

Nauðsynleg verkfæri:

HandsögHandsög
HandhefillHandhefill
PenslasettPenslasett
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

Efni fyrir þetta skref:

FuruborðFuruborð1 3/4 in front board
JárnnaglarJárnnaglar1 1 1/2 in cut nails
Flatstál úr mjúku stáliFlatstál úr mjúku stáli1 7/8 in hoop iron
TréskrúfurTréskrúfur1 3/4 in round-headed
OlíumálningOlíumálning1 stykki

Nauðsynleg verkfæri:

HandsögHandsög
HamarHamar
SkrúfjárnasettSkrúfjárnasett
PenslasettPenslasett
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

Efni fyrir þetta skref:

AskborðAskborð1 axle and felloes
HvíteikarborðHvíteikarborð1 spokes
JárnteinnJárnteinn1 3/8 in pins
TrétappiTrétappi4 1/4 in
Flatstál úr mjúku stáliFlatstál úr mjúku stáli1 3/4 x 1/8 in tyre

Nauðsynleg verkfæri:

TrérennibekkurTrérennibekkur
BugtarhefillBugtarhefill
Handsveifarbor með borHandsveifarbor með bor
HamarHamar
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

Efni fyrir þetta skref:

Flatstál úr mjúku stáliFlatstál úr mjúku stáli2 3/4 x 1/8 in irons
TréskrúfurTréskrúfur1 stykki
OlíumálningOlíumálning1 stykki

Nauðsynleg verkfæri:

SkrúfjárnasettSkrúfjárnasett
PenslasettPenslasett

Efni

10

Nauðsynleg verkfæri

12

Þessi teikning býr til

Thumbnail
Tímabundinn texti

Hjólbörur

Free

78
0

CC0 opinbert ríki

Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.

Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.

Umræða

(0)

Skrá inn til að taka þátt í umræðunni

Hleður athugasemdum...