Samvinna
LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Workbench: a Pine Bench with a Plank Top and Vise (Boy Mechanic, 1913)
A boy's first workshop bench: two mortised pine leg frames bolted to braces, a 3 1/2 ft top of one 2 x 12 in plank with a back board, a tool rack behind, and a wooden vise on an iron bench screw.
Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
Miðlungs
Unknown
Leiðbeiningar
1
1
Make the two leg frames
Make the two leg frames
Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.
Efni fyrir þetta skref:
Furutimbur1 2 x 4 in: legs, crosspiecesNauðsynleg verkfæri:
Handsög
Grópmeitill
Hamar2
2
Brace them together
Brace them together
Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.
Efni fyrir þetta skref:
Furutimbur1 2 x 4 in: braces
Vagnbolti4 3/8 x 6 inNauðsynleg verkfæri:
Handsög
Handsveifarbor með bor
Skiptilykill3
3
Fit the plank top
Fit the plank top
Make the main top M from one 2 x 12 in plank 3 1/2 ft long. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.
Efni fyrir þetta skref:
Harðviðarplanki1 2 x 12 in, 3 1/2 ft
Furuborð1 back board
Tréskrúfur1 longNauðsynleg verkfæri:
Handsög
Blokkhefill
Flatskrúfjárn4
4
Add the tool rack
Add the tool rack
Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.
Efni fyrir þetta skref:
Furuborð2 7/8 in, 3 1/2 ft
Naglar1 stykkiNauðsynleg verkfæri:
Handsveifarbor með borHandsögHamar5
5
Fit the vise
Fit the vise
Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).
Efni fyrir þetta skref:
Furutimbur1 2 x 6 block, 2 x 4 pieces, guide rails
Bekkjarskrúfa fyrir tréskurð1 stykkiVagnbolti1 for L and PNaglar1 stykkiNauðsynleg verkfæri:
HandsögGrópmeitillHandsveifarbor með borSkiptilykillHamarEfni
7- 1 2 x 6 block, 2 x 4 pieces, guide railsStaðgengill
- 1 for L and PStaðgengill
- 1 2 x 12 in, 3 1/2 ftStaðgengill
- 2 7/8 in, 3 1/2 ftStaðgengill
- 1 longStaðgengill
- 2 stykkiStaðgengill
- 1 stykkiStaðgengill
Þessi teikning býr til
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.