ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
FUTURO VERDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Building a Balafon — The West African Gourd-Resonated Xylophone
Woody

Creato da

Woody

3. luglio 2026NO
0
0
0
0
0

Building a Balafon — The West African Gourd-Resonated Xylophone

Build a balafon: a row of tuned wooden bars, each hung over its OWN tuned gourd resonator with a little buzzing membrane, struck with rubber-headed mallets. Cut and tune the bars by shaving, hang them on a frame over the gourds, and play. A serious maker build in the tuned wooden bar and the individually-tuned resonator.
Intermedio
Several hours over a couple of sessions

Istruzioni

1

Wooden bars over singing gourds

The balafon is a xylophone of tuned wooden bars, but each bar hangs over its own tuned gourd resonator with a small buzzing membrane, giving it a warm, humming, buzzy voice.
2

Cut the bars

Cut a set of hard, dense wooden bars in graduated lengths, longest to shortest, and dry them well. A shorter, thicker bar rings higher.

Materiali per questo passaggio:

Bloodwood BoardBloodwood Board1 pezzo

Strumenti necessari:

HacksawHacksaw
3

Tune the bars

Tune each bar by shaving wood away: hollow the MIDDLE of the underside to lower its note, or trim the ENDS to raise it — the same two cuts as any xylophone or marimba.

Strumenti necessari:

Sloyd Carving KnifeSloyd Carving Knife
4

Build the frame

Build an open frame — two long rails on legs — to carry the bars in a row with space beneath for the gourds.

Materiali per questo passaggio:

Dry Softwood BoardDry Softwood Board1 pezzo
PVA Wood GluePVA Wood Glue1 pezzo
5

Fit the gourd resonators

Hang a gourd of the right SIZE beneath each bar — a bigger gourd for a lower bar. Each gourd's air cavity is tuned to its bar so it swells that note like a bottle blown at the right pitch.

Materiali per questo passaggio:

Mature Bottle GourdMature Bottle Gourd6 pezzi
6

Add the buzzing membranes

Pierce a small hole in the side of each gourd and cover it with a thin membrane (traditionally spider-egg-sac film; tissue works). It buzzes when the bar sounds — the balafon's signature rasp.

Strumenti necessari:

AwlAwl
7

Hang the bars and play

Rest the bars on cords along the rails at their still points (nodes) so they ring freely, and strike them with two rubber-headed mallets.

Materiali per questo passaggio:

Abaca Tying TwineAbaca Tying Twine1 pezzo
Dowel RodDowel Rod1 pezzo
8

Compendium — the bar and its own resonator

The balafon is a tuned-bar idiophone, just like the gamelan's metal saron, and its bars follow the same physics: a struck bar bends and rings, higher when it is short, thick and stiff, and it is tuned by removing wood — hollow the middle to lower the note, trim the ends to raise it — while resting the bar on cords at its two nodes (the still points about a fifth in from each end) lets it ring freely. But the balafon differs from the saron in two ways. First its bars are WOOD, not bronze, giving a warmer, woodier tone. Second, and beautifully, every bar has its OWN resonator: a gourd hung beneath it whose air cavity is tuned to that bar's note, so it acts as a Helmholtz resonator (a bottle blown at just the right pitch) and swells that one note — exactly the job a marimba's metal tube does under each bar. And each gourd carries a small membrane over a side-hole that BUZZES sympathetically when the bar sounds, a built-in mirliton that adds the balafon's characteristic rasp, the same trick as the dizi's dimo. The balafon is ancient in West Africa — the Sosso Bala, a sacred balafon, is said to date from the thirteenth century — and it is a direct ancestor of the marimba, carried across the Atlantic and grown into the marimbas of Latin America.

Materiali

6

Strumenti richiesti

3

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...