Collaborazione
ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)
Penny

Creato da

Penny

2. novembre 2026DK
6
0
0
0
0

Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)

The equal-arm balance with its weights replaced by electricity. The pan sits on a coil in the gap of a permanent magnet. A load pushes it down; capacitor rings sense the smallest movement, and a servo drives just enough current through the coil to lift it back to its rest position. That current is the weight. Result: a balance that reads the weight in grams or ounces on a digital display, with no weights to handle, and tare by its circuit. Source: C. B. Akers and others (Arbor Laboratories), US Patent 4,034,819 (1977). Unknown: the resolution, capacity, magnet type, materials and sizes; the circuits are given as blocks only. Picture: patent drawing.
Avanzato
2 weeks

Istruzioni

1

Build the magnet circuit

Stack permanent magnets into a column with a soft iron core. Enclose them in an annular outer housing with end caps, shaped so the field crosses a narrow annular air gap at a constriction. Keep the whole structure symmetrical about its vertical axis. Mount it on a support plate fixed to an upright, such as a housing panel on a base. Not given: the magnet type, materials and sizes.

Materiali per questo passaggio:

Magnete piccoloMagnete piccolo1 column
Tondino di ferroTondino di ferro1 soft iron core
Metallo sconosciutoMetallo sconosciuto1 housing and end caps
Materiale sconosciutoMateriale sconosciuto1 support plate, panel, base

Strumenti necessari:

Set di cacciavitiSet di cacciaviti
Dimensioni sconosciuteDimensioni sconosciute
2

Hang the coil in the gap

Wind the coil tightly round the middle of a light bobbin that surrounds the core, the coil sitting in the air gap. Tabs at both ends of the bobbin pass out through holes in the end caps to suspension frames. Hang the frames from thin springy cantilevers fixed to the upright, so the bobbin can only move a short way straight up and down. Keep the bobbin and its suspension as light as possible. Put the weighing pan on top. Ours: enamelled wire.

Materiali per questo passaggio:

Filo di rame smaltatoFilo di rame smaltato1 coil
Materiale sconosciutoMateriale sconosciuto1 bobbin, frames, cantilevers
Piatto della bilanciaPiatto della bilancia1 pezzo

Strumenti necessari:

Dimensioni sconosciuteDimensioni sconosciute
3

Fit the capacitor rings

Mount four capacitor rings inside the outer housing, two above and two below the air gap, facing matching rings on the bobbin. Cross-connect them so a tilt of the bobbin cancels out and only up-and-down movement shows. Connect them to a signal generator: as the bobbin moves, one set's capacitance rises and the other's falls, and the difference becomes the control voltage.

Materiali per questo passaggio:

Metallo sconosciutoMetallo sconosciuto1 rings
Circuito integratoCircuito integrato1 sensing circuit
Filo per cablaggioFilo per cablaggio1 pezzo
Filo per saldaturaFilo per saldatura1 a little

Strumenti necessari:

Saldatore a stagnoSaldatore a stagno
4

Close the servo loop and read the current

Feed the control voltage to a d.c. servo that drives current through the coil, through a flexible lead, until the bobbin is back at its rest position. Pass that current through a large stable resistor, a thermal resistor that corrects for temperature and a calibration potentiometer: the voltage across them stands for the weight. A separate circuit (comparators, saw-tooth generator, oscillator and counter) turns it into a count read out as grams or ounces. Tare is ordinary circuit logic. Ours: a segment LCD; check with calibration weights.

Materiali per questo passaggio:

Circuito integratoCircuito integrato1 servo and counting circuits
ResistenzaResistenza2 stable resistor, thermal resistor
PotenziometroPotenziometro1 calibration
Display LCD a segmentiDisplay LCD a segmenti1 display
Filo per saldaturaFilo per saldatura1 a little

Strumenti necessari:

Saldatore a stagnoSaldatore a stagno
Set di pesi di taraturaSet di pesi di taratura

Materiali

12

Strumenti richiesti

4

Blueprint correlati

Questi blueprint condividono conoscenze โ€” tecniche, materiali o principi

CC0 Pubblico dominio

Questo progetto รจ rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...