Collaborazione
ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Rack-and-Pinion Opposed-Dasher Churn: Two Rows of Hanging Dashers Move Opposite Ways Through Slots in the Lid
Nelson Gabel of Gratis, Ohio, received US 33,080, dated 20 August 1861, for a box churn worked by racks and a pinion. Two slides lie on the lid over two slots, each carrying three dashers that hang down into the cream. A rack on each slide meshes a pinion between them, so when a lever on a standard pushes one slide to and fro, the other moves the opposite way. The currents meet and break against each other and the box's ends.
The patent gives no sizes; every size here is ours.
Intermedio
About 3 days
Istruzioni
1
1
Two rows passing each other
Two rows passing each other
Caricamento del notebook Jupyter…
2
2
A frame slid to and fro on the lid, a year and a half before
A frame slid to and fro on the lid, a year and a half before
Morgan's sliding frame spins beaters by a cord. Gabel's two slides carry the dashers themselves, and a pinion makes them move against each other.
3
3
Read US 33,080
Read US 33,080
"Thus it will be observed that when milk is put into the box and the lever (a) worked to and fro the agitation of the milk will be very great. As the currents each way will be broken and dashed in opposite directions the globules will thus be crushed both by sudden concussion against the side of the box and the violent reverse action of the currents."
4
4
Box A on legs, top B with two slots
Box A on legs, top B with two slots
Glue up a hardwood box A 600 x 300 mm inside and 300 deep from 20 mm boards, the joints sealed with silicone sealant, and screw four hardwood legs 40 x 60 mm, 220 long below it. Cut a 20 mm HDPE or hardwood top B to fit over the mouth, with two slots 30 mm wide and 500 long, 33 mm either side of the centre line, and a 12.6 mm hole at the centre for the shaft C.
Materiali per questo passaggio:
Tavola di legno duro4 pezzi
Colla da legno1 pezzo
Sigillante siliconico1 pezzo
Viti da legno30 pezzi
Lastra di HDPE1 pezzoStrumenti necessari:
Sega circolare da banco
Fresatrice verticale
Seghetto alternativo
Trapano a batteria
Serie di punte da trapano
Morsetto a barra
Set di cacciaviti
Metro a nastro5
5
Print the racks b (two)
Print the racks b (two)
A rack: 416 mm long, module 2.5, 20 mm thick. Print two, in halves if the bed is short. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Print the pinion a
Print the pinion a
The pinion: 16 teeth, module 2.5, 20 mm thick, 12.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Slides h, racks b, dashers k
Slides h, racks b, dashers k
Cut two hardwood slides h 560 x 50 x 25 mm and screw a rack b along the inner edge of each, teeth inward. Cut six 12 mm HDPE dashers 115 mm wide and 210 long; drill four 25 mm holes in four of them, the end ones. Screw each to a hardwood stem 20 x 20 mm, 90 long, and fix three stems under each slide, at its middle and 180 mm either side, to hang through the slot with the dashers 40 mm off the floor. Lay the slides on the top over the slots, racks facing.
Materiali per questo passaggio:
Tavola di legno duro1 pezzo
Filamento PETG1 pezzoLastra di HDPE1 pezzoViti da legno20 pezziColla da legno1 pezzoStrumenti necessari:
Stampante 3D a filamento (FDM)Sega circolare da bancoSeghetto alternativo
Set di punte a lanciaTrapano a batteriaSerie di punte da trapanoSet di cacciaviti8
8
Shaft C, pinion a and strap D
Shaft C, pinion a and strap D
Cut a 12 mm stainless shaft C 90 mm long, stand it in the top's centre hole and pin the pinion a on it meshing both racks. Bend a mild steel flat bar strap D over the pinion and the slides, bore it 12.6 mm over the shaft's top, and screw its feet to the top beyond the slides.
Materiali per questo passaggio:
Barra di acciaio inossidabile1 pezzoFilamento PETG1 pezzo
Piatto di acciaio dolce1 pezzoViti da legno4 pezzi
Coppiglia1 pezzoStrumenti necessari:
Seghetto per metalli
Lime (lima a mano)
Morsa da bancoTrapano a batteriaSerie di punte da trapanoSet di cacciaviti9
9
Lever d, standard m and lever f
Lever d, standard m and lever f
Bolt a mild steel flat bar lever d, 470 mm long, to the outer slide with a spacer block, reaching past the box's end. Make a standard m of two hardwood posts 30 x 20 mm joined at the foot, standing beside the box's end and reaching 260 mm above the top, with a 10 mm bolt across their tops. Hang a flat bar lever f between them on the bolt, its lower end slotted over a bolt through the end of d and its upper end a handle.
Materiali per questo passaggio:
Piatto di acciaio dolce2 pezziTavola di legno duro1 pezzo
Assortimento di bulloni a testa esagonale3 pezzi
Dado autobloccante con inserto in nylon3 pezzi
Rondella piana6 pezziColla da legno1 pezzoViti da legno6 pezziStrumenti necessari:
Seghetto per metalliLime (lima a mano)Morsa da bancoTrapano a batteriaSerie di punte da trapano
Chiave regolabile a rullinoSega circolare da banco10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the box's front wall cut away: the two rows of hanging dashers (the end ones holed), the slides on the top with their racks and the pinion under its strap, and the levers d and f on the standard.
11
11
Churn
Churn
Lift the top off with the slides and dashers, pour about 20 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, and set the top back. Work the lever f to and fro through its full swing, timing it. When the butter comes, lift the top and dashers out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiali per questo passaggio:
Panna da montare20 l
Sale marino grosso1 pezzo
Acqua1 pezzoStrumenti necessari:
Termometro a sonda permanente
Cronometro
Bilancia digitale da cucina
Grande ciotola da impasto in acciaio inossidabile12
12
Troubleshooting
Troubleshooting
Rack-and-pinion churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Nelson Gabel** of Gratis, Preble County, Ohio, US 33,080, 20 August 1861, "Churn". He claimed "the employment and arrangement of fixed pinion (a), double reciprocating racks (b b) and slides (h h)". His text calls the hand lever both (a) and (f). He gives the dashers only as drawn, three to a slide with holes in the end ones; ours are plain boards. The patent gives no sizes; every size here is ours.
Materiali
15- 4 pezziSegnaposto
- 3 pezziSegnaposto
- 1 pezzoSegnaposto
- 60 pezziSegnaposto
- 1 pezzoSegnaposto
- 2 pezziSegnaposto
- Segnaposto
- 2 pezziSegnaposto
- 1 pezzoSegnaposto
- Segnaposto
- Segnaposto
- 6 pezziSegnaposto
- 20 lSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
Strumenti richiesti
18- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
File di progetto
3Questo progetto realizza
Blueprint correlati
Questi blueprint condividono conoscenze — tecniche, materiali o principi
Sliding-Frame Churn: Push and Pull a Frame on Top and a Cord Spins Tilted, Perforated Beaters Back and Forth
di Buttercup
Lavorazione del legno
1
0
0
0
0
0
Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It
di Buttercup
Lavorazione del legno
0
0
0
0
0
0
Adjustable-Valve Dash Churn: Hinged Perforated Wings Shut Going Down, Open Coming Up, Slides Set How Big the Holes Are
di Buttercup
Lavorazione del legno
1
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
di TheChef
MESTIERE
60
0
0
0
0
0
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.