Collaborazione
ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Creato da

Forge

13. novembre 2026NO
6
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Intermedio
8-15 minutes a pair, once practised

Istruzioni

1

Bar length and sizes

Caricamento del notebook Jupyter…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Materiali per questo passaggio:

Barra di ferro battutoBarra di ferro battuto1 pezzo

Strumenti necessari:

Metro a nastroMetro a nastro
MatitaMatita
Fogli di carta pesanteFogli di carta pesante
Forgia da fabbroForgia da fabbro
Tagliolo da incudineTagliolo da incudine
Tenaglia da forgiaTenaglia da forgia
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Strumenti necessari:

Forgia da fabbroForgia da fabbro
Bicornia a beccoBicornia a becco
SlittaSlitta
Martello da imbutireMartello da imbutire
Tenaglia da forgiaTenaglia da forgia
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Strumenti necessari:

Bicornia a beccoBicornia a becco
Martello da imbutireMartello da imbutire
Tenaglia da forgiaTenaglia da forgia
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Strumenti necessari:

Bicornia a beccoBicornia a becco
Fuller (ferro da scanalare)Fuller (ferro da scanalare)
SlittaSlitta
Martello da imbutireMartello da imbutire
Tenaglia da forgiaTenaglia da forgia
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Strumenti necessari:

Bicornia a beccoBicornia a becco
Punzone a caldoPunzone a caldo
Punzone da chiodaturaPunzone da chiodatura
Martello da imbutireMartello da imbutire
Tenaglia da forgiaTenaglia da forgia
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Strumenti necessari:

Forgia da fabbroForgia da fabbro
Bicornia a beccoBicornia a becco
Martello da imbutireMartello da imbutire
Fuller (ferro da scanalare)Fuller (ferro da scanalare)
Punzone a caldoPunzone a caldo
Punzone da chiodaturaPunzone da chiodatura
Tenaglia da forgiaTenaglia da forgia
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Materiali

1

Strumenti richiesti

12

Questo progetto realizza

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...