ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI

The Spring-Button Lemon Squeezer: A Button That Gives Way So the Rind Wraps Round It
A flat squeezer presses only the middle of the lemon's cut face, and the rind at its edge keeps its juice.
John Klepzig of San Francisco, California, received US 84,125, dated 17 November 1868, for "forming an opening in one of the squeezing-levers. A movable button, which is operated by a spiral spring, is placed in the opening, and, by placing the fruit between the two levers, and closing them, the juice is expressed, through the hole in the bottom, into the tumbler, while the rind of the lemon is pressed closely against the face of the button-lever, completely enclosing the button." A projection on the other lever pushes the fruit down onto the button.
This rung works out the lever's force and the spring's share, with a work check, then makes the levers in hardwood with a sprung, grooved button and a hollow stem, and squeezes lemons over a tumbler.
Intermedio
About 4 hours
Istruzioni
1
1
Lever and spring
Lever and spring
Caricamento del notebook Jupyter…
2
2
A hinged squeezer before it
A hinged squeezer before it
The embedded blueprint squeezes the lemon between two cups on crossed handles. Klepzig uses two hinged levers and lets a sprung button give way under the fruit.
3
3
Read US 84,125
Read US 84,125
"A and B are the two levers, connected by a hinge, C. The lever A has a projection, D, so that when the two levers are shut together, the small end of the button E, which sets in the openings in the lever B, is forced out."
"The segregated half of the fruit is placed against the spring-button, and the opposite lever, having the projection, is brought down upon the small end, which presses the rind down upon the smooth surface of the button-lever, completely surrounding the button, and bearing down the spring, which forces out the stem, while the juice of the fruit passes through the centre hole, H, into the tumbler. The face of the button is concave and has grooves centring to the opening."
4
4
Make the levers and squeeze lemons
Make the levers and squeeze lemons
**Levers.** Cut two 25 cm levers from hardwood board, shaped like Klepzig's with handles at one end, and join the other ends with a butt hinge as C.
**Button seat.** Drill a 45 mm stepped hole through lever B, 7 cm from the hinge, narrower at the back to leave a ledge.
**Button.** Turn or rasp a hardwood button that slides in the hole, with a concave face carved with grooves running to a centre hole, and fix a short length of tube through its centre as the stem G, passing through the narrow back of the hole. Put a compression spring round the stem, resting on the ledge.
**Projection.** Glue a rounded hardwood knob to lever A opposite the button as the projection D.
**Test.** Seal the wood with food-safe oil. Hold the squeezer over a tumbler, lay a half lemon cut face down on the button, close the levers and press. Weigh the juice against a half squeezed on a flat board.
Materiali per questo passaggio:
Tavola di legno duro1 pezzo
Blocco di legno duro2 pezzi
Cerniera a libro1 pezzo
Viti da legno6 pezzi
Tubo di alluminio0.05 metro
Assortimento di molle a compressione1 pezzo
Colla da legno1 pezzo
Limone2 pezziStrumenti necessari:
Sega a mano
Trapano a batteria
Serie di punte da trapano
Serie di scalpelli da legno
Raspa
Carta abrasiva
Set di cacciaviti
Coltello da cucina
Bilancia digitale da cucina
Bicchiere5
5
A button that sticks, leaks or does not wrap the rind
A button that sticks, leaks or does not wrap the rind
Spring-button lemon squeezer troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**John Klepzig** of San Francisco, California, received US 84,125, dated 17 November 1868. The opening in lever B was smaller at the back than at the face, leaving a ledge on which the spiral spring F rested, and the small end or tube G attached to the button passed through the lesser hole. His claim is the movable button with its opening and spiral spring, with the two levers.
**Honest limits.** Hardwood levers, a carved button and a bought spring stand in for his made-up parts. The notebook ignores friction; its forces, lengths and spring are examples. Your juice weights are the result.
Materiali
8- 1 pezzoSegnaposto
- 2 pezziSegnaposto
- 1 pezzoSegnaposto
- 6 pezziSegnaposto
- 0.05 metroSegnaposto
- Segnaposto
- 1 pezzoSegnaposto
- 2 pezziSegnaposto
Strumenti richiesti
10- Segnaposto
- 1 vendor sell this, none ship to you yetSegnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
Questo progetto realizza
Blueprint correlati
Questi blueprint condividono conoscenze — tecniche, materiali o principi

The Porcelain-Lined Lemon Squeezer: Cast-Iron Handles, Porcelain Where the Juice Runs
di Mary
Ceramica
39
0
0
0
0
0

The Shears-Cup Lemon Squeezer: Two Cups on Crossed Handles, a Slotted Recess for the Juice
di TheChef
Lavorazione dei metalli
35
0
0
0
0
0

The Law of the Lever — Archimedes' Balance of Weight and Distance
di Martin
Fisica
63
0
0
0
1
0
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.
