Collaborazione
ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle.
Painted red inside and light green outside, lined in a lighter colour and black.
Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Intermedio
Unknown
Istruzioni
1
1
Make the hales
Make the hales
Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.
Materiali per questo passaggio:
Tavola di frassino1 hales 3 ft 1 in x 1 5/8 x 1 1/2 inStrumenti necessari:
Sega a mano
Pialla a mano
Pialletto a due manici2
2
Frame with oak cross-pieces
Frame with oak cross-pieces
Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.
Materiali per questo passaggio:
Tavola di quercia bianca1 pezzo
Spina di legno1 3/16 in pinsStrumenti necessari:
Saracco a costola
Scalpello da mortase
Graffietto
Trapano a manovella con punta
Falsa squadra3
3
Fit the legs and stays
Fit the legs and stays
Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.
Materiali per questo passaggio:
Tavola di quercia bianca1 legs 1 1/2 in square, stays
Bullone a testa tonda e collo quadro4 3 inStrumenti necessari:
Sega a manoTrapano a manovella con punta
Set di cacciaviti4
4
Bottom and sides
Bottom and sides
Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.
Materiali per questo passaggio:
Tavola di pino1 1/2 in bottom, 5/8 in sides
Colore a olio1 pezzoStrumenti necessari:
Sega a manoPialla a mano
Set di pennelli5
5
Front board and ironwork
Front board and ironwork
Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.
Materiali per questo passaggio:
Tavola di pino1 3/4 in front board
Chiodi di ferro1 1 1/2 in cut nails
Piatto di acciaio dolce1 7/8 in hoop iron
Viti da legno1 3/4 in round-headedColore a olio1 pezzoStrumenti necessari:
Sega a mano
MartelloSet di cacciavitiSet di pennelli6
6
Make the wheel
Make the wheel
Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.
Materiali per questo passaggio:
Tavola di frassino1 axle and felloesTavola di quercia bianca1 spokes
Tondino di ferro1 3/8 in pinsSpina di legno4 1/4 inPiatto di acciaio dolce1 3/4 x 1/8 in tyreStrumenti necessari:
Tornio per legnoPialletto a due maniciTrapano a manovella con puntaMartello7
7
Hang the wheel and paint
Hang the wheel and paint
Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.
Materiali per questo passaggio:
Piatto di acciaio dolce2 3/4 x 1/8 in ironsViti da legno1 pezzoColore a olio1 pezzoStrumenti necessari:
Set di cacciavitiSet di pennelliMateriali
10- 1 axle and felloesSegnaposto
- 1 spokesSegnaposto
- 4 1/4 inSegnaposto
- Segnaposto
- 1 3/4 in front boardSegnaposto
- 3 pezziSegnaposto
- 1 1 1/2 in cut nailsSegnaposto
- 2 3/4 x 1/8 in ironsSegnaposto
- 1 pezzoSegnaposto
- 1 3/8 in pinsSegnaposto
Strumenti richiesti
12- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
Questo progetto realizza
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.