アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Fit: A Joint That Needs a Mallet Is Too Tight
A joint you have to drive home with a mallet will not be stronger for it. It will be weaker, because the fibres are crushed, there is nowhere for the glue to sit, and the glue that was there has been scraped off on the way in.
The target is a joint that goes together with firm hand pressure, or at most a few light taps, and stays together on its own when you let go. That leaves a glue line a few hundredths of a millimetre thick, which is what modern wood glues are formulated for.
A slack joint is also a bad joint, and for the opposite reason: PVA has essentially no gap-filling ability, so a visible gap is a joint held by a brittle film of dried glue. The useful range between the two is narrow, and it is worth knowing in numbers.
中級者
3 hours
手順
1
1
How tight is right, in numbers
How tight is right, in numbers
Jupyter ノートブックを読み込み中…
このステップの材料:
堅木の板1 個
木工用ボンド（PVA）1 個必要な工具:
すきまゲージセット
デジタルノギス 6インチ
デスクトップパソコン2
2
Pare to fit, and pare the right piece
Pare to fit, and pare the right piece
Push the joint together until it binds, then look for the shiny spots — where it has rubbed is where it is tight. Pare those and only those. Taking a shaving off the whole cheek turns a tight joint straight into a slack one.
A sharp chisel takes a controlled shaving; a dull one skips and digs. Fitting is the operation that most rewards a freshly honed edge, and most punishes a tired one.
Pare the part that is hidden. On a mortise and tenon, pare the tenon rather than the mortise walls, because the tenon disappears. On a dovetail, pare the pins.
このステップの材料:
堅木の板1 個必要な工具:
のみ
万力（ベンチバイス）デジタルノギス 6インチ3
3
Fit dry, and only once
Fit dry, and only once
Assemble the whole thing dry, check it for square and for wind, and take it apart again. That is the dry-run rung, and this is the rung where it pays: a joint discovered to be tight with glue in it is a genuine emergency.
Assemble dry as FEW times as possible. Wood compresses a little each time, so a joint tested five times is looser than the one tested once. If a joint is right, leave it alone.
Number the joints as you take them apart. Hand-fitted joints are fitted to each other and are not interchangeable, and a pencil mark on the inside face saves finding that out during the glue-up.
このステップの材料:
堅木の板1 個必要な工具:
組み合わせスコヤ
捻れ確認用定規対
バークランプ4
4
The clamps are for holding it, not for closing it
The clamps are for holding it, not for closing it
If the joint needs clamp pressure to close, it does not fit. Clamps are there to hold surfaces in contact while the glue cures, and to squeeze the line thin — not to drag parts into position.
A frame pulled square by clamps springs back out of square the moment they come off, because nothing has changed about the geometry of the parts. The shoulders are what make it square, and clamps cannot fix a shoulder.
Which makes the whole batch one argument. The wood will move whatever you do; the joint holds because its long grain is glued and its shape interlocks; and the fit is what decides whether the glue line is a bond or a filler. None of those can be corrected with pressure at the end.
このステップの材料:
木工用ボンド（PVA）1 個必要な工具:
バークランプ組み合わせスコヤ関連ブループリント
これらのブループリントは知識を共有しています — 技術、材料、原理
CC0 パブリックドメイン
このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。
メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。