コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)
Forge

作成者

Forge

14. 11月 2026NO
6
0
0
0
0

Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)

The fixed smith's hearth George Edwinson told Amateur Work readers to build (1886): stone below, firebrick in fireclay on top, every course bound with hoop iron, a 4 in. iron rim forming the hearth pan, a fire back and tuyere made from a 1 in. plate and a bored 14-pounder iron shot, a slanting flue, a 10 x 10 x 22 in. slake trough, and a clinker floor.
中級者
Two to three days of building

手順

1

His sizes

Jupyter ノートブックを読み込み中…
2

Read Edwinson

"The foundation of this structure up to within one foot of the top may be of stone, but the finishing courses should be of firebrick."
3

Build the base

Build the hearth in stone up to 1 ft (30 cm) below the top, binding every course with pieces of hoop iron. Leave an arch at the back for the coal pit and the blast pipe (figs. 4, 5). Overall size is ours: fit it to your shop.

このステップの材料:

石のブロック石のブロック1 個
鉄の輪鉄の輪1 個
耐火粘土耐火粘土1 個

必要な工具:

左官ごて左官ごて
水準器水準器
4

Make the fire back and tuyere

Bore a 3/4 in. hole through a 14-pounder iron shot and open it to a 1 in. taper on one side. Cut and countersink a hole in a 1 in. iron plate to take a third of the shot, and drill four 1/2 in. holes to bolt the plate through the wall with nuts and fish plates. (Or buy a fire back and tue-iron.)

このステップの材料:

鉄の玉(バラスト)鉄の玉(バラスト)1 個
鉄の板鉄の板1 個
六角ボルト詰め合わせ六角ボルト詰め合わせ1 個

必要な工具:

ボール盤ボール盤
鍛冶炉鍛冶炉
ハンマーハンマー
5

Firebrick top and back

Lay the top courses and the back wall round the tuyere in firebrick bedded and jointed with fireclay, still binding each course with hoop iron. Build in the fire back with the shot as the tuyere, and leave a slanting flue hole just above it (fig. 5).

このステップの材料:

耐火れんが耐火れんが1 個
耐火粘土耐火粘土1 個
鉄の輪鉄の輪1 個

必要な工具:

左官ごて左官ごて
水準器水準器
6

Fit the slake trough

Before the last course, set in a water trough 10 in. deep and wide and 22 in. long, of sheet iron, cast iron or stone, inside the rim line; bolt a sheet-iron one to the rim. A sheet-iron division riveted across gives a coal trough too.

このステップの材料:

軟鋼板軟鋼板1 個
鉄リベット鉄リベット1 個
水水1 個

必要な工具:

ボール盤ボール盤
ハンマーハンマー
7

Bind with the rim

Bind the top course with a rim of 1/4 x 4 in. iron, half below the brick edge and half above it to make the hearth pan, its ends bolted to the back wall with 3/8 in. bolts built into the brickwork.

このステップの材料:

鉄の板鉄の板1 個
六角ボルト詰め合わせ六角ボルト詰め合わせ1 個

必要な工具:

鍛冶炉鍛冶炉
金床金床
ハンマーハンマー
ボール盤ボール盤
8

Connect the blast

Bring the pipe from a fan or bellows under the arch to the back of the tue-iron. He reckons about 150 cu ft (4.2 m3) of air a minute for a welding heat: a 9 in. fan at about 360 rpm or a double-action bellows.

必要な工具:

送風機送風機
9

Lay the floor

Ram wetted smiths', foundry or boiler clinkers sprinkled with a little Portland cement hard and level, with a thin layer of smithy cinder ashes beaten on top. Stone or ordinary concrete floors misbehave when hot iron is dropped on them.

このステップの材料:

ポルトランドセメントポルトランドセメント1 個
水水1 個

必要な工具:

ハンマーハンマー
10

Troubleshooting

Hearth troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" I, **Amateur Work, Illustrated**, vol. V (1886), pp. 161-162 and figs. 2, 4, 5 (checked on the archive.org scan amateurworkillus05lond). He gives no overall hearth size; that and the metric figures and tools are ours.

材料

11

必要な工具

7
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー

この設計図で作るもの

関連ブループリント

これらのブループリントは知識を共有しています — 技術、材料、原理

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...