アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Extruded Polystyrene Foam
Emma

作成者

Emma

22. 9月 2026SE
1
0
0
0
0

Extruded Polystyrene Foam

Carl Munters had shown that polystyrene heated with methyl chloride under pressure puffs into a closed-cell foam when let out of the vessel (US 2,023,204) - but only in small pieces; with larger outlets the mass collapsed into brittle, irregular lumps. Otis Ray McIntire at Dow found the fix: keep the mass BELOW the critical temperature of methyl chloride, about 143 °C, so the gas stays dissolved, and let its own evaporation cool the foam fast enough to freeze the cells. **US 2,450,436**, "Manufacture of cellular thermoplastic products", McIntire, assigned to Dow Chemical, filed 26. July 1947, granted 5. October 1948. Its drawing is the pressure vessel with the bottom valve the foam flows out of. Dow sold the result as blue insulation board; the white bead foam of packaging is a later process. **Methyl chloride is toxic; you start from foam board.** You build a hot-wire cutter, cut an insulated box, and measure how long it keeps ice.
初心者
3 hours plus an ice test

手順

1

The cutter

Base on two feet, a post and an arm; the wire runs from the arm tip down through the base to a spring underneath.
デザインファイルBLENDCC0 - Free
2

Build the frame

From 18 mm plywood cut a 300 x 300 mm base, two 300 x 40 mm feet, a 280 x 50 mm post and a 200 x 50 mm arm. Glue and screw the post to the back edge and the arm square on top.

このステップの材料:

合板合板1
木ねじ木ねじ10
木工用接着剤木工用接着剤20 ml

必要な工具:

手のこぎり手のこぎり
コードレスドリルコードレスドリル
ドライバーセットドライバーセット
鋼尺鋼尺
3

String the wire

Drill 2 mm through the arm tip and the base directly below. Fix the wire to an eye bolt on top of the arm, run it down through the base, and tie it to a spring under the base so it stays taut when it expands hot. Check it is square to the table.

このステップの材料:

ニクロム線 80/20、0.64 mmニクロム線 80/20、0.64 mm1 メートル
アイボルトアイボルト1
圧縮ばねセット圧縮ばねセット1 セット

必要な工具:

コードレスドリルコードレスドリル
ドリル刃セット(収納ケース入り)ドリル刃セット(収納ケース入り)
4

Power it

Clip leads to the wire at the arm and below the base. Set the bench supply to 1.5 V with a 4 A limit and raise it slowly (notebook) until the wire slides through a scrap cleanly. Ventilate.

必要な工具:

可変直流電源可変直流電源
Alligator to Alligator CablesAlligator to Alligator Cables
N95 防じんマスクN95 防じんマスク
透明保護メガネ透明保護メガネ
5

Cut the box

From 25 mm foam board cut a base and lid 200 x 200 mm, two sides 200 x 150 mm and two 150 x 150 mm. Feed slowly - let the wire do the work. Tape the box together.

このステップの材料:

押出発泡ポリスチレン板押出発泡ポリスチレン板1
マスキングテープマスキングテープ1

必要な工具:

鋼尺鋼尺
6

Weigh a cube

Cut a 50 mm cube from an offcut and weigh it for the notebook.

必要な工具:

デジタルキッチンスケールデジタルキッチンスケール
7

The ice test

Put 500 g of ice in a bag in the foam box and another 500 g in a cardboard box of the same size, side by side in the same room. Note the room temperature and check both every hour until the ice is gone.

このステップの材料:

氷1000 g
段ボール箱段ボール箱1

必要な工具:

デジタルキッチンスケールデジタルキッチンスケール
室温計室温計
8

Wire, density, heat leak

Jupyter ノートブックを読み込み中…
9

History & Context

**What the patent specifies:** polystyrene with methyl chloride dissolved under pressure below the gas's critical temperature, released through an outlet so evaporation expands and cools it into uniform closed cells, in blocks 2 inches thick or more. **Modern build (derived):** commercial extruded foam board, today made with other blowing agents. The patent names its target plainly: blocks big enough to cut into insulating panels for refrigerators. Its limits: it melts at low heat, burns unless treated, dissolves in many solvents (and in some glues and paints), and breaks down in sunlight.
ステップ 9 - Image 1

材料

10

必要な工具

11

設計ファイル

1

関連ブループリント

これらのブループリントは知識を共有しています — 技術、材料、原理

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...