コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Iron Tube: Butt-Welded by Drawing Through Dies on a Draw Bench (Whitehouse, 1825)
Forge

作成者

Forge

4. 11月 2026NO
12
0
0
1
0

Iron Tube: Butt-Welded by Drawing Through Dies on a Draw Bench (Whitehouse, 1825)

Cornelius Whitehouse's way of making welded iron tubes, the basis of butt-weld pipe ever since: a strip of flat iron is turned up into a tube with its edges meeting, heated nearly to fusion in a hollow fire, and pulled by the chain of a draw bench through a pair of dies, which press the hot edges together and weld them. The tube is welded in two halves, one end at a time. Whitehouse made tubes 2 to 8 ft long in one piece, smooth inside and out. Unknown: plate thickness, width and tube sizes. The source does not give them. Source: Whitehouse's specification of 1825, quoted in C. D. Terry, Butt Weld Pipe (1907). Picture: Terry's Figs. 4 and 5.
上級者
Unknown

手順

1

Turn the plate over

Take a piece of flat iron (plough-plate iron) of a thickness and width to suit the intended bore. Bend up its sides ('turn it over') until the edges meet, or nearly so, and it forms a long tube. Ours: hammer and anvil for the bending.

このステップの材料:

錬鉄の平鋼錬鉄の平鋼1 flat plough-plate iron
不明な寸法不明な寸法1 個

必要な工具:

鍛造槌鍛造槌
平面の鉄床平面の鉄床
2

Heat in the hollow fire

Put the tube into a hollow fire, urged by a blast, and heat it until the iron is on the point of fusion. Ours: a smith's forge as the hollow fire.

必要な工具:

鍛冶炉鍛冶炉
鍛冶ばさみ(やっとこ)鍛冶ばさみ(やっとこ)
3

Draw it through the dies

Clamp the end of the tube to the chain of the draw bench, driven by a hand winch or an engine. Draw it out of the fire through a pair of dies of the size wanted, set in a screw press and closed to their bearing, so that the hot edges are pressed together and welded. A pair of pinchers with a conical hole, held against a standard, may be used instead of the press and dies.

必要な工具:

引抜台(ドローベンチ)引抜台(ドローベンチ)
鍛冶ばさみ(やっとこ)鍛冶ばさみ(やっとこ)
4

Weld the other half

Open the clamp and take the tube off. Grip the other end, put the unwelded part into the fire, heat it, and draw it through the dies in the same way.

必要な工具:

鍛冶炉鍛冶炉
引抜台(ドローベンチ)引抜台(ドローベンチ)
鍛冶ばさみ(やっとこ)鍛冶ばさみ(やっとこ)

材料

2
  • 1 flat plough-plate iron
    プレースホルダー
  • プレースホルダー

必要な工具

5

この設計図で作るもの

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...