アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes
The bee skep is the coiled-straw beehive that housed honeybees across Europe for roughly two thousand years, from antiquity into the 1800s, before wooden box hives replaced it. Using the same coiling technique as a straw basket, long rye straw is wound into a dome and stitched together with split cane. This blueprint builds a traditional skep by hand — from preparing the straw to the finished, weatherproofed hive ready to house a swarm.
中級者
8
手順
1
1
Harvest and clean long rye straw
Harvest and clean long rye straw
Cut long rye or wheat straw and strip off the seed heads and leaf sheaths, keeping the hollow stems long and unbroken for strong coils.
このステップの材料:
ライ麦わら1 束必要な工具:
ナイフ2
2
Split and soak the binding cane
Split and soak the binding cane
Split lengths of cane into thin flexible strips and soak them in water until pliable — these will sew the straw coils together.
このステップの材料:
割り竹1 束
水3 リットル必要な工具:
ナイフ3
3
Make the girth gauge
Make the girth gauge
Form a small open ring about 2.5 cm across (the traditional 'girth', often a cow-horn tip). Straw fed through it keeps every coil the same thickness.
必要な工具:
藁巣箱の周径ゲージ4
4
Bind the crown
Bind the crown
Take a small handful of straw, bend it into a tight knot to form the top knob of the skep, and lash it firmly with a strip of split cane.
このステップの材料:
ライ麦わら1 束割り竹1 メートル必要な工具:
目打ち（キリ）5
5
Feed straw into an even rope
Feed straw into an even rope
Pass straw through the girth to form a continuous rope of even thickness, adding a few stems at a time so the bundle never thins as you work.
このステップの材料:
ライ麦わら1 束必要な工具:
藁巣箱の周径ゲージ6
6
Sew the first coils to the crown
Sew the first coils to the crown
Coil the straw rope in a tight spiral around the crown. Push the awl through the coil below, pass split cane through, and pull each stitch snug about every 2 cm.
このステップの材料:
割り竹1 メートル必要な工具:
目打ち（キリ）7
7
Spiral outward to start the dome
Spiral outward to start the dome
Continue spiralling outward from the crown, binding each new coil to the one below. The domed top of the hive begins to take shape.
このステップの材料:
ライ麦わら1 束割り竹1 メートル必要な工具:
目打ち（キリ）8
8
Build the domed wall downward
Build the domed wall downward
Work the spiral down and out to build the wall, keeping the girth on the rope to hold thickness and every binding stitch tight and evenly spaced.
このステップの材料:
ライ麦わら1 束割り竹1 メートル必要な工具:
目打ち（キリ）藁巣箱の周径ゲージ9
9
Keep the courses even
Keep the courses even
Control how far each coil steps outward so the dome stays smooth and symmetrical. Steady, even courses make a strong, weathertight hive.
このステップの材料:
ライ麦わら1 束必要な工具:
目打ち（キリ）10
10
Widen to the finished base
Widen to the finished base
As you near the bottom, let the coils reach the finished diameter of about 35–40 cm — the standard size for a colony of bees.
このステップの材料:
ライ麦わら1 束割り竹1 メートル必要な工具:
目打ち（キリ）11
11
Cut the flight entrance
Cut the flight entrance
At the lower edge, cut a small entrance notch in a coil so the bees can come and go once the skep is set open-side down.
必要な工具:
ナイフ12
12
Finish and lock the base coil
Finish and lock the base coil
Complete the last coil at the base, taper off the straw rope, and lock the final binding stitches so the skep cannot unravel.
このステップの材料:
割り竹1 メートル必要な工具:
目打ち（キリ）13
13
Trim the skep clean
Trim the skep clean
Trim protruding straw ends and stray cane with the knife to leave a clean rim and an even outer surface.
必要な工具:
ナイフ14
14
Clom the outside for weatherproofing
Clom the outside for weatherproofing
Smear a thin coat of cow-dung-and-clay daub over the straw to shed rain and seal drafts, then let it dry — the traditional 'clomming'.
このステップの材料:
牛糞2 kg
ボールクレイ（蛙目粘土）1 kg15
15
Cure the finished skep
Cure the finished skep
Cure the skep in a dry, airy place. Once fully dry it is ready to hive a swarm — set open-side down on a board or stand.
材料
5- 1 束プレースホルダー
- 1 メートルプレースホルダー
- 3 リットルプレースホルダー
- 2 kgプレースホルダー
- 1 kgプレースホルダー
この設計図で作るもの
関連ブループリント
これらのブループリントは知識を共有しています — 技術、材料、原理
CC0 パブリックドメイン
このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。
メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。