コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)
Forge

作成者

Forge

13. 11月 2026NO
7
0
0
0
0

Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)

James H. Reinhardt of East Orange, New Jersey, received US 1,261,438, dated 2 April 1918, for a profile gauge: a row of pins clamped between two thin metal members. Rubber tubes wrapped in cloth press on the pins, so each one slides when pushed and stays where it is left. Pressed against an object, the pin ends take its outline, and a pencil drawn along them copies it, so the shape can be made again. We build his single gauge from brass sheet and steel wire. All sizes are ours.
中級者
About 5 hours

手順

1

How many pins

Jupyter ノートブックを読み込み中…
2

Read US 1,261,438

"The rods or pins 3 of the respective gages may be pushed against the surface of the object, as required, to obtain its outline along the ends of the rods or pins, whereby a pencil may be drawn along the ends of the pins to trace such outline or contour of the object. From such outlines objects corresponding to the master object may be reproduced either in relief or concave according to which way the outline drawn from the ends of the rods is used."
3

Make the two members

Cut two strips of 0.8 mm brass sheet 200 x 32 mm (ours) with tin snips and file the edges. Bend 4 mm down along each long side in the vice, so each strip becomes a shallow channel 24 mm wide: his "gutter-like form". Clamp them together, open sides facing, and drill a 3.5 mm hole through both, 50 mm from each end, on the middle line.

このステップの材料:

真鍮板真鍮板2 個

必要な工具:

金切りばさみ金切りばさみ
ヤスリセットヤスリセット
万力(ベンチバイス)万力(ベンチバイス)
けがき針けがき針
ハンドドリルハンドドリル
4

Make the gutters

Cut two strips of the same brass 180 x 14 mm and bend each round a 6 mm rod into a U that will hold the rubber tube, his gutters 10. Rivet them inside one member, one near each long side, with copper rivets, keeping clear of the screw holes.

このステップの材料:

真鍮板真鍮板1 個
銅リベット銅リベット6 個

必要な工具:

金切りばさみ金切りばさみ
軟鋼丸棒軟鋼丸棒
万力(ベンチバイス)万力(ベンチバイス)
ハンドドリルハンドドリル
片手ハンマー(球頭)片手ハンマー(球頭)
5

Make the retainers

Cut two pieces of 6 mm rubber tubing 170 mm long and push a 2 mm wire through each, his cores 9, "to somewhat stiffen them". Wrap each in a strip of cotton cloth, lap its edges and glue them with contact cement, his protecting cloth 12, so the rubber does not touch the metal. Lay one in each gutter.

このステップの材料:

ゴム管ゴム管1 個
鋼線鋼線1 個
木綿布木綿布1 個
接着ゴム系ボンド接着ゴム系ボンド1 個

必要な工具:

ニッパーニッパー
はさみはさみ
6

Cut the pins

Cut 1 mm steel wire into pins 120 mm long, as many as the notebook gives. Straighten any that are bent and file both ends flat and smooth, so they slide easily and do not mark the work.

このステップの材料:

鋼線鋼線1 個

必要な工具:

ニッパーニッパー
精密ヤスリ(針ヤスリ)セット精密ヤスリ(針ヤスリ)セット
万力(ベンチバイス)万力(ベンチバイス)
7

Assemble

Lay the member with the retainers open side up. Lay the pins across it side by side, touching, centred so equal lengths stick out on both sides; leave a gap at each screw hole (ours). Put the other member on top and pass a machine screw through each hole with a nut. Tighten them evenly until each pin slides when pushed but does not fall.

このステップの材料:

小ねじ小ねじ2 個
六角ナット六角ナット2 個

必要な工具:

ドライバーセットドライバーセット
モンキーレンチモンキーレンチ
8

Take a profile

Push all the pins level with a flat board. Press the gauge square against the object until the pins have taken its shape. Lift it off, lay it on paper or on the stock to be cut, and draw a pencil along the pin ends.

必要な工具:

鉛筆鉛筆
9

Troubleshooting

Pin profile gauge troubleshooting.

Flow

Loading...
10

History and honest limits

**James H. Reinhardt** of East Orange, New Jersey, US 1,261,438, dated 2 April 1918, filed 20 June 1914. He claimed "a profile gage comprising a pair of opposed members, rods or pins located between and transversely with respect to said members, means for clamping said members together" and "a resilient retainer comprising spaced rubber tubes". His members can have teeth along their edges, and his patent also covers end castings that join several gauges in a line or at an angle, a smaller gauge clamped between them, a toothed spacer strip and a rubber-mat retainer: none of those are built here. He gives no sizes: the brass, the 200 mm length, the 1 mm pins, the tube and core sizes, the cement, the rivets and the screws are ours.

材料

8
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • 2 個
    プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー
  • プレースホルダー

必要な工具

13

関連ブループリント

これらのブループリントは知識を共有しています — 技術、材料、原理

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...