コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
Buttercup

作成者

Buttercup

11. 11月 2026IE
0
0
0
0
0

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow

Moses D. Wells of Morgantown, Virginia, received US 31,756, dated 19 March 1861, for a churn dasher shaped as a slanted open box: two flat end plates carrying the journals, two curved face pieces with lips at opposite corners, and two open sides. It turns on a horizontal axis in a box whose bottom is curved to its sweep. Turned fast it churns; turned the same way slowly, it gathers the butter inside itself, the lips keeping it from being thrown out, so it lifts out in a lump. The patent gives no sizes; every size here is ours.
中級者
About 2 days

手順

1

Churning fast, gathering slow

Jupyter ノートブックを読み込み中…
2

A round-bottomed box with a turning dasher, eight months before

Park's box works the butter with pins. Wells's hollow dasher gathers it inside itself.
3

Read US 31,756

"The dasher being hollow, a few slow turns of the same causes the butter to collect within the box so as to be removed in a lump. ... The object of the diagonal lips b', b', is, to gather the butter against, and prevent it from being thrown out of the box in turning it around."
4

Body B with a curved bottom, legs and lid

Glue up two hardwood ends 22 mm thick, 350 mm wide and 320 tall. On each draw the inside: a 300 mm half circle with its centre 160 mm up, and straight sides rising 150 mm above the centre to the top. Rout a groove 1.6 mm wide and 8 deep on that line. Cut a slot 16.6 mm wide down from the top edge to the centre, rounded at its foot, as the journal bearing, and a hardwood keeper that fills the slot above the journal. Bend a 1.5 mm stainless sheet 416 mm long into a U to fit the line, set it in both grooves with silicone sealant, and screw hardwood sides 22 mm thick outside its straight parts. Screw four hardwood legs 40 x 40 mm, 390 long, to the ends, splayed out. Cut a hardwood lid 444 x 350 x 22 mm, notched over the keepers, with a 25 mm air opening o.

このステップの材料:

堅木の板堅木の板4 個
ステンレス鋼の板ステンレス鋼の板1 個
シリコーンシーラントシリコーンシーラント1 個
木工用接着剤木工用接着剤1 個
木ねじ木ねじ30 個

必要な工具:

テーブルソーテーブルソー
方位磁針方位磁針
ジグソージグソー
ルータールーター
木工のみセット木工のみセット
ゴムハンマーゴムハンマー
コードレスドリルコードレスドリル
ドリルビットセットドリルビットセット
スペードビットセットスペードビットセット
バークランプバークランプ
ドライバーセットドライバーセット
メジャー(巻尺)メジャー(巻尺)
5

Print the end plates a (two)

An end plate of the dasher: 15 mm thick, the slanted outline of Fig. 1 with curved top and bottom edges, a 50 mm boss at the centre. Print two; drill each 16 mm at the centre for a journal. PETG, 0.2 mm layers, 30 % infill, 4 walls.
デザインファイルSTLCC0 - Free
6

Dasher D: end plates a, face pieces b with lips b', journals

Cut two strips of 1.5 mm stainless sheet 360 mm long, each 160 mm wide; bend each to a curve of about 300 mm radius following the end plates' curved edges, with a 20 mm lip b' at one long edge turned on round the corner. Screw them to the end plates' curved edges, the lips at diagonally opposite corners, leaving the two slanted sides open. Push a 16 mm stainless journal into each end plate's boss and pin it: one 40 mm long, the other 90 mm for the crank. Lay the journals in the slots and drop in the keepers. Pin a crank of mild steel flat bar, 120 mm throw, with a hardwood handle, on the long journal.

このステップの材料:

PETGフィラメントPETGフィラメント1 個
ステンレス鋼の板ステンレス鋼の板1 個
木ねじ木ねじ16 個
ステンレス鋼の丸棒ステンレス鋼の丸棒1 個
割りピン割りピン3 個
軟鋼平鋼軟鋼平鋼1 個
堅木のダボ堅木のダボ1 個

必要な工具:

FDM 3D プリンターFDM 3D プリンター
金切りばさみ金切りばさみ
ゴムハンマーゴムハンマー
コードレスドリルコードレスドリル
ドリルビットセットドリルビットセット
金切りのこ(ハクソー)金切りのこ(ハクソー)
やすり(手やすり)やすり(手やすり)
万力(ベンチバイス)万力(ベンチバイス)
ドライバーセットドライバーセット
7

The build in 3D

FreeCAD model of this build, cut open: the round stainless bottom in grooved ends with slotted bearings and keepers, the legs and lid with its air opening, and the slanted hollow dasher with its curved, lipped face pieces and crank.
デザインファイルBLENDCC0 - Free
8

Churn and gather

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, so it stands below the axis, and put on the lid. Turn the crank briskly, timing it. When the butter comes, turn the same way slowly for a few turns until it gathers inside the dasher. Lift off the lid and keepers, lift the dasher out by its journals, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

このステップの材料:

生クリーム生クリーム10 l
粗い海塩粗い海塩1 個
水水1 個

必要な工具:

差しっぱなしのプローブ温度計差しっぱなしのプローブ温度計
ストップウォッチストップウォッチ
デジタルキッチンスケールデジタルキッチンスケール
ステンレス鋼の大きな混ぜ鉢ステンレス鋼の大きな混ぜ鉢
9

Troubleshooting

Box-dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**Moses D. Wells** of Morgantown, Monongalia County, Virginia (now West Virginia), US 31,756, 19 March 1861, "Churn-Dasher". He claimed "the oblique box dasher D constructed and operating substantially as set forth, that is to say, with two flat sides, two curved sides, and two open sides, and turned in the same direction for churning, and for gathering the butter, but at various velocities". He says only that the journals have "suitable connections to facilitate the removal of the dasher"; ours lie in open slots under keepers. The patent gives no sizes; every size here is ours.

材料

13

必要な工具

21

設計ファイル

2

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...