コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Shoe Horn With a Rolled Tubular Tang, Cut From One Sheet (Williams, 1901)
Forge

作成者

Forge

13. 11月 2026NO
10
0
0
0
0

Shoe Horn With a Rolled Tubular Tang, Cut From One Sheet (Williams, 1901)

Alfred G. Williams of Newark received US 685,548, dated 29 October 1901, for a sheet-metal shoe horn whose handle tang is part of the same blank. A tongue at the narrow end is rolled into a close tube, and two wings beside it are folded over the edges of the horn, so the weak neck is stiffened where it meets the tang. A handle fits on the tang. We cut it from brass sheet with a 1:1 template and fit a hardwood handle. All sizes are ours.
初心者
About 3 hours

手順

1

How wide to cut the tongue

Jupyter ノートブックを読み込み中…
2

Read US 685,548

"I construct the tang by extending the sheet metal from the upper or smaller end of the horn in a tongue of suitable width to roll into a tubular tang and form integral with such tongue lateral wings or flanges upon the upper end of the horn, which can be folded or curved upon the edges of the horn to stiffen the same at its junction with the tang."
3

Print the template

The blank at 1:1 as his Fig. 1: body a, wings b, tongue c, with the fold lines a' dashed: they run from where each wing starts in to the root of the tongue. print at 100 % (check the 50 mm bar).
デザインファイルPDFCC0 - Free
4

Cut the blank

Cut the paper blank out and lay it on 0.8 mm brass sheet. Scribe round it. Cut just outside the line with tin snips, then file to the line. Keep the tongue an even 15 mm wide.

このステップの材料:

真鍮板真鍮板1 個

必要な工具:

けがき針けがき針
金切りばさみ金切りばさみ
ヤスリセットヤスリセット
万力(ベンチバイス)万力(ベンチバイス)
5

Smooth the edges

Round every edge of the body with a file and sandpaper. The mouth slides against the heel and the sock, so it must be smooth all round.

必要な工具:

ヤスリセットヤスリセット
紙やすり紙やすり
6

Roll the tang

Lay a 4 mm rod along the middle of the tongue. With round-nose pliers, curl one edge of the tongue up round the rod, then the other, a little at a time along its length, until the edges meet: his "close-rolled cylindrical" tang c'. Slide the rod out.

必要な工具:

丸口ペンチ丸口ペンチ
平やっとこ平やっとこ
軟鋼丸棒軟鋼丸棒
7

Fold the wings

Fold each wing b along its dashed line a' over the edge of the horn, onto the underside, with the flat-nose pliers and then light taps of the rubber mallet, until it lies close. His Figs. 3 and 4 show the horn turned over, with the wings b' lying on the edges and running into the tang.

必要な工具:

平やっとこ平やっとこ
ゴムハンマーゴムハンマー
8

Dish the body

His body is "slightly concave transversely". Lay it, inside up, across a rod held in the vice and tap the edges down with the rubber mallet, working from the neck to the mouth, until it is evenly hollow across its width. Keep the curve slight; it should still lie nearly flat on the bench along its length.

必要な工具:

ゴムハンマーゴムハンマー
軟鋼丸棒軟鋼丸棒
万力(ベンチバイス)万力(ベンチバイス)
9

Make the handle

Saw 75 mm of hardwood handle stock (ours) and shape it with a rasp and sandpaper. Drill a 6 mm hole 40 mm deep in one end, straight down the middle, to take the tang. His handle is "more for ornament than for support", so any shape you like will do.

このステップの材料:

柄用の堅木材柄用の堅木材1 個

必要な工具:

金切りのこ(ハクソー)金切りのこ(ハクソー)
木工やすり(荒目)木工やすり(荒目)
紙やすり紙やすり
ハンドドリルハンドドリル
万力(ベンチバイス)万力(ベンチバイス)
10

Fit the handle

Roughen the tang with sandpaper, mix the epoxy, fill the hole and push the handle onto the tang until it meets the wings. Line the handle up with the horn and leave it to set as the epoxy's label says.

このステップの材料:

二液性エポキシ二液性エポキシ1 個

必要な工具:

紙やすり紙やすり
11

Polish

Polish the horn with polishing compound on a soft cloth.

必要な工具:

研磨剤(つや出し用)研磨剤(つや出し用)
12

Troubleshooting

Tubular-tang shoe horn troubleshooting.

Flow

Loading...
13

History and honest limits

**Alfred G. Williams** of Newark, New Jersey, assignor to Havell Manufacturing Company, US 685,548, dated 29 October 1901, filed 26 June 1901. He claimed "the shoe-horn having integral tang c', of close-rolled cylindrical form, with integral wings b' extended from such tang and folded over upon the edges of the horn". He meant it for "ornamented handles" in "mounted toilet sets". He gives no sizes, no metal and no way of fixing the handle: the brass, all sizes, the hardwood handle, the epoxy and the order of work are ours.

材料

3

必要な工具

14

設計ファイル

1

この設計図で作るもの

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...